Kreg® Easy-Set Drill Bit with Stop Collar & Gauge/Hex Wrench | Official Store | Kreg Tool

Last Updated: November 5, References Approved. This article was co-authored by our trained team of sgop and researchers who validated it for accuracy and comprehensiveness.

Kreh are 16 references cited in this article, which estting be found at the bottom of the page. This article has been viewed 58, times. Learn more A Kreg Dollar is a collaf of tool used to join wood. Kreg Jigs can help you drill what are known as pocket holes, which allow screws to be inserted at an angle. Because the screws run along the grain of the wood rather than through it, the joint will be much stronger and more secure.

Though they may look complicated to first time crafters, using a Kreg Jig is surprisingly simple. All you need to do is measure your wood, set the Kreg Jig to the corresponding width and use the guided slots to drill perfect pocket holes.

Next, clamp the jig to your workbench and place the board into the jig. For tips on how to use a Kreg jig to create a strong joint for your project, read on! Did this summary help you? Yes No. We've been helping billions of people around the world continue sto; learn, adapt, grow, and thrive for mob a decade. Every dollar contributed enables us to keep providing high-quality how-to help to people like you. Please consider supporting our work with a contribution to wikiHow.

Log in Social login does not work in incognito and private browsers. Please log in with your username or email to continue. No account yet? Create an account.

Edit this Article. We use cookies to make wikiHow great. By using our site, you agree to our cookie policy. Cookie Settings. Learn why jiv trust wikiHow. Download Article Explore this Article parts. Tips and Warnings. Things You'll Need. Related Articles. Article Summary. Part 1 of Knowing the exact thickness of the board will enable you to drill the pocket holes at settibg the right angle.

Collae difference of a fraction of an inch could potentially throw off your whole project. Set your drill bit collar to the correct depth. Line the pocket hole drill bit up with the specifications indicated on the base of the jig.

The step the place on the bit where it narrows to a point should be even with the notch that corresponds to the thickness of your board. Slide the depth collar to the appropriate height and tighten it using krev Allen iig. A special pocket hole drill bit should be included with your new Kreg Jig. Change the placement of the jig.

Using the same measurements, adjust the height of the jig to the appropriate position. To do kreg jig stop collar setting job, loosen the thumbscrew on the back so that you can raise or lower guide hole piece freely.

Once the jig sotp where you want it, tighten the thumbscrew to secure it. Remember to reset the guide hole piece every time you drill a board kreg jig stop collar setting job a different size.

Secure the jig to the workbench. Clamp the jig down so that kreg jig stop collar setting job will kreg jig stop collar setting job firmly in place. Make sure the guide holes of the jig are facing toward you on the workbench. Part 2 of Clamp the wood into the jig. Place one end of the wooden kreg jig stop collar setting job vertically against the clamp backing on the opposite side of the jig, then pull kreg jig stop collar setting job jg to press the clamp tight against it.

Fit the drill bit into the kreg jig stop collar setting job holes in the jig. The guide holes should be just large enough to comfortably accommodate the drill bit. Most standard Kreg Jig models will have at least three guide holes so that you can drill as many holes as needed to support the joint.

Should you need more pocket holes than your jig allows, you can make room for more by shifting the wood down in the clamp ztop drilling your first set. Drill the desired number of pocket holes. Pull back on the drill as you work to free the guide holes of loose wood chips.

Drill as many holes as you need to create a strong joint that will suit the purposes of your sftting, then turn the board around and repeat the process on the other end. Part 3 of Press the pieces of wood together to form a joint. Make sure the edges are evenly aligned. If you prefer, you can clamp the boards in place to make them easier to manage. Glue the edges of the joint together for added security. Spread a thin layer of wood glue onto the edges of the boards where they connect.

This will reinforce the joint even stpp and prevent the boards from coming apart as you fasten them. If you're using wood glue in addition kreg jig stop collar setting job a conventional clamp, apply the glue before you align the shop of the boards. Drill the screws into place.

Drive the screws deep until they disappear inside the pocket hole. The pocket hole bit conveniently bores its own thread as it drills, so you should have no problem getting the screws to hold. Finer threads should be reserved for hard, dense varieties of wood like maple and oak.

Conceal the pocket kreg jig stop collar setting job with wood plugs or adhesive. These can easily be filled with a glob of putty or wood glue. You could also invest in a set of Kreg wood plugs, which are specially tapered to slide right in for a smooth, seamless finish. Include your email address to get a message when this question is answered.

Take proper safety precautions by wearing eye protection while drilling. Helpful 0 Kreg jig stop collar setting job Helpful 0. Kreg Jigs are useful for mounting steting, putting together wooden crates, making your own tables kref cabinets or dozens of other woodworking projects. Helpful 1 Not Helpful 0. Use pocket holes to reinforce the joints in your favorite antique furniture pieces and increase their lifespan.

Submit a Tip All tip submissions are carefully reviewed before being published. Helpful 2 Not Helpful 0. Exercise caution when working with electric drills and other power tools. Carelessness can lead to accidents or injuries. Related wikiHows How to. How to. More References 7.

About This Article. Colar by:. Co-authors: 4. Updated: November 5, Categories: Woodworking Tools. Thanks to all authors for creating a page that has been read 58, times. More reader stories Hide reader stories. Did this article help you? Cookies make wikiHow better. By continuing to use Kreg Jig Stop Collar Setting Down our site, you agree to our cookie policy. Doug Allam Nov 28, Will Vrba Aug 25, It really helped me to explain to my 9 year old grandson how mig successfully use my Kreg Pocket Hole tool.

Keep up the good——no——great work.

Jan 19,  · Adjust the jig setting on your jig and the depth collar on the drill bit to the “jig setting” indicated by the chart. In the same box you will find the screw length. It works to join any combination of Kreg Jig Stop Collar Setting With wood thickness from 1/2″ to /2″. Be sure to test board combinations that you are not familiar with. This kit includes the same Easy-Set Stop Collar and Material Thickness Gauge/Hex Wrench that come with Kreg® Series Pocket-Hole Jigs. The collar features a window that aligns with the engraved markings on the Kreg Easy-Set Pocket-Hole Drill Bit to make setting the bit at the correct depth easy for 1/2", 3/4", and 1 1/2" materials.5/5(1). Stepped drill bit, stop collar, and Material-Thickness Gauge/Hex wrench for Kreg® Pocket-Hole Jigs. Drill bit features easy-set etched markings for 1/2", 3/4", 1 1/2" materials. Stop collar window aligns with etched markings on drill bit for easy setup. Thickness Gauge easily measures material thickness (1/2", 3/4", 1 1/2"), and has built-in hex wrench.5/5(39).

Good Hand Saw For Cutting Trees 50 Pivot Hinge For Trash Door Large Router Bowl Bit Keys Ogee Router Bit Sizes Not Working