inch Deluxe Pro Band Saw. Models: JWBSDXPRO. (Shown with optional Rip Fence). JET. New Sanford Road. LaVergne, Tennessee Part No. M Ph.: Revision C1 10/ - Copyright © JET. - document is bookmarked.  Mounting the Table to the Bandsaw. Grounding Instructions. Volt Operation. Volt Conversion. Extension Cords. Adjustments. Tilting the Table. 14" deluxe pro Bandsaw The all-new (patented) JWBSDXPRO 14" Bandsaw from JET® has been completely redesigned from top to bottom to meet the needs of today’s most demanding woodworkers. Gone are the days of adding a riser block; this 14" bandsaw comes with a newly redesigned massive upper and lower cast iron frame specifically designed to handle much higher blade tensioning with virtually no frame deflection.  14" Deluxe pro bandsaw • Built-in 12" resaw capacity for cutting larger pieces of wood •2  Speed poly-v belt drive system •N  ewly designed upper and lower cast iron frame for increased strength and rigidity. New enclosed stand with storage shelf and easy access door. Specifications Stock Number Model. USD. The JWBSDXPRO 14" Deluxe Bandsaw from JET (shown here with optional fence) has been designed to meet the needs of today's most demanding woodworkers. Gone are the days of adding a riser block; this 14" bandsaw comes wit. JET Logo Report any damage immediately to your distributor and shipping agent. Support Plate-short. Cancel Delete. Table of Contents. Excludes sawing fluids.

Make sure the blade is tensioned with the release lever in the down position as seen in Fig. Turn blade tension knob Fig. The blade width gauge D, Fig.

Never adjust blade tracking with the machine running! The blade should track in the center of both wheels. Never operate the bandsaw without all guards in place and in working order!

Disconnect machine from the power source. Verify guide post is parallel to blade by checking position of bearings with respect to blade when the guide post is raised all the way up and again in the lowest position.

If the bearings have shifted throughout the travel of the guide post then it needs to be adjusted. Page Optional Accessories Non-proprietary parts, such as fasteners, can be found at local hardware stores, or may be ordered from JET.

Some parts are shown for reference only, and may not be available individually. Upper Arm Frame Table Pin Locking Knob Table Insert Spring Pin Button Head Socket Screw Motor Cord Power Cord Self Tapping Screw Flat Washer Lock Washer Wheel Brush Phillips Pan Head Machine Screw The arrangement of these fasteners is shown in Figure 5.

Page 11 To mount table, remove table insert and table pin see Figure Orient the table so that the saw blade will pass through the slot in the table and into the center opening.

Continue holding up the table, and turn the With the aid of a second person, lift the saw body out of the shipping container and place onto stand top.

Screw the two small knobs Figure 17 into the threaded holes in the saw body. Slide the pulley cover down over the knobs, and tighten the knobs. Attach trunnion support bracket to saw body Page Grounding Instructions To mount the table, remove pin and insert from the table Figure Orient the table so the saw blade will pass through the slot in the table and into the center opening.

Continue holding up the table, and rotate the table so the two screws Page Volt Operation The band saw must comply with all local and national codes after the volt plug is installed.

The band saw with a volt plug should only be connected to an outlet having the same configuration Figure No adapter is available or should be used with the volt plug. Page Extension Cords Make sure the cord is in good condition, and heavy enough to carry the current your band saw will draw.

An undersized cord will cause a drop in line voltage, resulting in loss of power and overheating. Page Changing Blades 90 degrees with the blade. If necessary, adjust scale pointer to zero. Changing Blades Blade teeth are sharp! Use care when handling the saw blade. Failure to comply may cause serious injury. Disconnect machine from power source. Loosen blade tension by turning the tension knob counterclockwise Figure Page Adjusting Blade Tracking As you become more experienced with the saw, you may find it necessary to change the blade tension from the initial setting.

Changes in blade width and the type of material being cut will have an effect on blade tension. Never operate the band saw without all guards in place and in working order.

Blade must already be tensioned and tracking properly. Page 20 Notice the bearing holder on the shaft is eccentric. Gone are the days of adding a riser block; this 14" band saw comes with a massive cast iron frame for increased power that makes it ready to meet all resaw expectations head-on.

Couple this incredible feature with a new high tension spring design and many more amazing features, and you have a band saw that will last for years to come. Only registered users can write reviews. Please, log in or register.

The following shipping offers are available within the 48 contiguous United States:. Shipping charges applied to subtotal prior to any taxes and after any discounts. View all terms. Band Saw Blades Direct. Enter your measurement in inches below to convert to ft. We send technical documents, sharp tips, and periodic promotions for band saw blades -- some exclusive ONLY to email subscribers!

Register Log In My Cart 0.

Lidl Belt And Disc Sander 2020 August Mortise And Tenon Jig For Drill Press Inc