Review with videos: JESSEM Clear Cut TS Stock Guides | FINE TOOLS

Hi, Guest Login Register. Pages: [ 1 ] Go Down. Author Topic: Jessem router guides on table saw Read times. AndrewG Posts: I recently purchased jessem table saw guides review china set of the jessem router guides to use on my Incra router fence.

I was wondering if anyone uses the router guides on their table saw? Thanks for your input! Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual.

Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Revie makes no jessem table saw guides review china about the accuracy, reliability, completeness or timeliness of the material on this website or about the results to be obtained from using the jessem table saw guides review china. Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material.

Your use of any material contained on this website is entirely at your own risk. The content contained on this site is provided for informational purposes only and does not constitute professional advice. Alanbach Posts: Rrview am no Engineer and not an expert by any means but I have both so let me give it a shot. The router guides will work on your table saw.

There have been a number of posts lately showing exactly that. The router guides are smaller and have a smaller capacity.

Both types of Jessem guides perform the same functions, they pull the material into the fence, they hold it down and they prevent it from going back the way it came. The simple difference is capacity and flexibility. The router guides tabpe the thickness of the piece according to how fhina on the fence they are mounted.

The TS guides swing out from their mounting position on top of the fence and by the nature of their design and their size that can hold down a much thicker workpiece. The more complicated difference is the inherent power of a Table Saw vs. The TS guides have larger rollers and so I am sure that the one way device inside that wheel is probably stronger gides the router guides and therefore able to do the job it is designed for on the machine it was designed to operate on.

So for me the bottom line is that I personally for me would be totally comfortable with the router guides working on a Table Saw for smaller work. Jessem table saw guides review china work, however, would make me a little more hesitant, ie. I hope that this helps! Jessem table saw guides review china Posts: DynaGlide - yes, there it is.

Thank you. And beautiful job, by the way. If you move the guides up to the top slot what will the thickest piece of lumber that you will be able to fit under it? Thank you for the reply and posting the link, not sure how I missed that.

Alanbach Thank you for the kind words. If I locate the guides in the top track and raise them completely I would be able to fit a 2. AndrewG I have only put 5" wide boards through so far.

My tablesaw is tiny and I bought it for ripping narrow pieces down to width. It's great for filling that need especially with the guides. Anything larger than a guide rail and I'd be tempted to use a track saw. I already owned the router guides and felt unsafe running long boards through my jobsite saw.

When I bought the saw I had already intended on adding an aluminum subfence longer than the table to provide better infeed support. The lightbulb went jessej when I saw I could get one with t track to use the Jessem router guides.

Mike Goetzke Posts: Just my opinion: I have both sets too. The router table clear-cut stock guides came out first and I bought them. I liked them so much I immediately purchased the TS stock huides when they came out. Sww mentioned if you put these two guides next to each other there is no questioning which one should be used on the TS. I'm in the camp if you are purchasing the stops for safety not jessem table saw guides review china to pull the wood toward the fence don't even think about using the much smaller guides on the TS.

ChuckM Posts: TealaG Posts: I only have the clear cut saw guides and one difference is that the saw guides can extend away from the fence, which may be an advantage for certain cuts? I sort of wonder whether I could use the table saw units on a router table?

Pages: [ 1 ] Go Up. SMF 2. Jessem table saw guides review china by DzinerStudio.

Description The Clear-Cut TS™ Stock Guides for your table saw offer superior control of your work achieving safer, smoother and more precise cuts with your work held securely in position. Unique guide rollers mounted on a 5° angle effectively steering your stock . The JessEm Clear-Cut TS Stock Guides for your table saw offer superior control on your workpiece by securely holding it in position to achieve safer, smoother, and more precise cuts. The unique guide rollers mounted on a 5-degree angle effectively steering your stock towards your fence. This angle causes the roller to hold with more force if the wood tries to move against the direction of the /5(). Jessem Rout-R-Lift II - Preliminary Review & Purchasing Experience. AM by Kurt T. Kneller | 3 comments» Well, my new Jessem Rout-R-Lift II finally was delivered today. This review is preliminary at this time and still need to complete my router table before using it. So, I can only comment on whole experience to date.

Tung Oil Price Philippines Router Bits And Their Uses Services Barnes Foot Mortiser For Sale 77 Intarsia Woodworking Projects Kathy Wise School