Staining a fiberglass door can be accomplished either hanging on the frame, attached to each other and vertical multiple doors or on saw horses. Jackie K. Another solvent door can be used is denatured alcohol. Always test stain on a hidden area of the wood to verify desired color. Thank you in advance for your help.

Wait at least eight hours and up to 24 hours or longer depending on. Refer to the instructions on the back of the polyurethane label. Apply in the same sequence as the stain application.

A minimum of two coats is recommended, waiting six hours between coats. Brushes should be cleaned with mineral spirits. Should you elect to stain rather than paint the outside of your door, follow steps These products will provide ultimate protection against sun exposure, water, and weather. The Gel Stain can also be used to stain the doorjamb, door frame, and mullions. Keep in mind as you are staining that it is better to start light on the stain application. If a darker color is desired, apply a second coat of the stain in the same manner as the first coat.

When recoating, allow a minimum of hours, depending on drying conditions. Low temperatures and high humidity will increase drying time. DANGER: Rags, steel wool, sanding residue, and other wastes used or soaked with oil-based products may spontaneously catch fire if improperly discarded.

No ignition source is required for these wastes to start on fire by themselves. Immediately place rags, steel wool, sanding residue, and other wastes used or soaked with these products in a sealed, water-filled metal container.

Dispose of in accordance with local fire regulations. Fiberglass Doors Staining Guide. Posted on November 6, Products used:. Additional Supplies. Phillips screwdriver Masking tape and paper Hammer Saw horses padded Extra cleaning rags Putty knife Utility knife These instructions are designed for use on all fiberglass, carbonite, composition, and other simulated wood grain surfaces, as well as stainable door frames.

Before You Begin. A Few Basics Thoroughly read and follow all the instructions as printed in this brochure and carefully read through product labels. Review suggested supplies on the back page and gather additional supplies. Provide a good working environment, one that is free of dust and has adequate lighting and ventilation. Ventilation is important in the application of stains and finishes. Please read product cautions carefully. Remove the door from its hinges and place on flat padded saw horses or substitute supports.

Remove all hardware hinges, doorknobs, locks, and weather stripping. Yes, a second is possible. Make sure to wait for the first coat to dry completely, typically several hours or overnight.

If you apply the second coat to soon it could reactivate the first coat smearing it around. I need to strip the stain and top coat to restrain my 3 year old fiberglass door.

I used gel stain and a polyurethane topcoat over factory base. What is the best product and process to use to strip topcoat and stain? Klean-Strip Fiberglass Paint Stripper is one of the best and is fiberglass safe. Finish up with a washing with plain water. You might need to use Lacquer Thinner after the washing to remove some stubborn spots.

Do you recommend one or two coats of stain? I just worry that with 2 coats it may just look painted. Is one coat durable enough with the urethane coat? Thanks Tiffany. More than one coat of stain is just about the look.

You can use as many coats as you feel is needed to get the look your after. I would do two coats of urethane for a more durable finish. What type of urethane would you recommend over a fiberglass door with gel stain finish?

The Helmsman spar will work well. I would stick with an oil base product for its ease of application but waterborne urethanes also will work, make sure what is used is recommended for exterior use.

Is it possible to get a light oak finish over the tan base of a fiberglass door, or will I have to prime it in a buff tone? Seems that mid tone and darker gel stains are all that I am seeing applied successfully. Also, does the interior side require a top coat? The light oak color is very difficult to achieve over typical dark tan fiberglass.

The buff color will be needed. Try to choose an eggshell sheened oil base paint if available, easier to stain over. Plus Old Masters makes the best gel stains, in my opinion. The lower section of our fiberglass door was weathered.

I use a wiping stain instead of a gel stain. Color is fine but not sure what else to do or if I have to remove???

All you need t do now is apply a clear coat to protect the new stain color from the elements. Any exterior rated finish will work; varnish, polyurethane or water based acrylic. I have tried re-applying, using a touch up stain marker, with no success. Is there a touch up product for scratches on a fiberglass door? It is possible the scratches are into and damaged the embossing wood grain.

It is impossible to fix this type of damage. Try an artist brush and the gel stain, carefully apply to the scratch only and reapply when dry if needed.

I have a thermatru wood grain front door that is under a porch roof, never receives sun or rain and the original mahogany colored gel stain was never top coated. To refinished this door I cleaned the inside and outside door with lemon pine sol as I read that this product did not require a rinse and did not leave a residue. Then my painter simply restained the door with dark mahogany Zar oil based interior wood stain. One coat. The door is beautiful.

My question is must I top coat? I would prefer not to because I may need to reapply another coat of stain and did not want to get involved with taking off the top coat.

How long would this finish last without a top coat? You should get a couple good years out of the new stain before recoating.

Just put the top coat on yesterday. It looked beautiful with just stain. Can this be fixed? Need a little info; What top coat was used, how was it applied and what was the weather conditions?

Plus, is the door finish cloudy? This will help figure out what happened and how best to fix. It was the Therma Tru top coat that came with the Therma Tru stain. It was brushed on. The weather was mid eighties, clear. The door finish is not cloudy. It was beautiful. The top coat turned cloudy within an hour after applying it. If I remember correctly this finish is a water based exterior acrylic urethane. Brushing is very difficult with this finish, dries too quickly.

Applying it too thick could cause this problem. This is a very helpful thread. I have a Jeld-Wen patio door fir texture that I need to stain. I need to test some colors on fiberglass to be sure I have a good match but there was no sample included with the door. I wrote to Jeld-wen but have not been able to get a response.

Is there a way to get a sample of fiberglass from some other source to test my stains? Can I test them on a different surface, like a board painted to match the base color of the door? Also, what do you recommend for a durable, long lasting outdoor top coat?

Thank you. Using a painted board is your best bet. It is probably the toughest exterior clear coat you can get. I had the glass replaced in my fiberglass door and need to know how to stain plastic glasss trim to match stained door.

This is on the interior side as we had exterior painted. First you need to prime the plastic trim then Gel Stain Application On Fiberglass Door Unit paint it a medium tan color, this will match the original color of the door.

Could also use a tinted primer, ask you local paint store if they can tint it to a tan color. Now you need some gel stain or heavy bodied wiping stain that matches or comes close to the door stain color. Application is by brush, might take more than one coat. Protect the rest of the door with blue painters tape and masking paper or news paper. After the stain is applied and dry apply a coat or 2 of sealer, polyurethane or varnish.

Might be a good time to re-coat the entire door. I just had a ThermaTru fiberglass entry door installed. I painted the outside to avoid the weathering of stain.

However, I wanted the wood look inside, so I stained it and the sidelights with Varathane gel stain, Ipswich Pine color, two coats. It looks beautiful now, before I have topcoated. I see someone commented that the inside needs to have a topcoat. Please advise as to reasons for top coating the inside. A clear coat will protect the stain from fading and damage.

Applying a clear coat, varnish or poly, can be a challenge but careful and apply only thin coats problems can be minimized. I would choose an oil base finish, fast drying polyurethane is good. Water based finished can present problems as they dry too fast and are harder to apply by hand. I have just had a therma-try door installed. I stained both sides of the door yesterday afternoon and it came out nicely, other than having to pluck hairs off from the brush supplied with the Therma-try recommended Same Day Stain Kit.

Do I need to remove more, even though the door looks good, or will it eventually dry. If I let it go too long without putting on the top coat will there be a problem? Thank You! Let it dry. With high humidity and somewhat low temps it could take a few days.

Keep check it and when dry apply a clear coat to protect the good looking stain. When I stained my Therma Tru door, even though the stain can said 24 hours, it really took more like four days for it to dry to not tacky at all! But it did eventually dry completely. Do I need to sand between sealer coats? I tried and it started taking off the stain?

At most a light careful sanding with or ultra fine sanding block. If you are taking off the clear coat, and getting down to the stain, then stop and apply more clear coat. All your looking or feeling for is having no dust on the door. I have a fiberglass front door that was stained and covered with an unknown type of top coat.

The sun has impacted the door and I want to refinish it. Should I sand the door to get the existing top coat off? Thank you for your assistance. Exact procedures depends on the door. Sanding is great for flat areas and solid wood doors. Intricate details are hard to sand. These areas will require using a paint stripper. The same paint stripper could be used on the entire door then sanded later to finish up with a smooth surface ready for stain.

No need to use a special exterior stain. Ant regular wood stain will do since you will be protecting it with a clear coat. I do recommend McCloskey Man-o-War spar varnish, good results over many years of use. It will do well applied over any proper wood stain. Hello — fiberglass front door had some damage from dog scratches. Planning on stripping and re-staining, but wondered if there was any solution to make sanded areas where scratches were better?

If this is a smooth fiberglass door then the Bondo will work. But, this sounds like a door with a wood grain texture. Good Luck! Everyone on here is talking about staining but I was wondering what kind of paint is best to use on a fiberglass door.

It is a jeld-wen door. The type of fiberglass, epoxy or poly, is irrelevant as the door will need priming anyway. A good universal acrylic primer will work well. Any type of paint can be applied to the door, the same type as your house is fine. Better the quality the better looking and longer lasting is the paint job. My fiberglass door is stained with gel stain and finished with poly sealer. Do I have to strip before restraining? Not necessarily.

If the existing stain and finish is in OK shape then just 1 a good cleaning, 2 very light sanding to remove any embedded dust, and 3 final cleaning with a solvent deglosser is a good base for the application of more oil based gel stain and then finish. Did you stain and treat the white trim around the window the same as the door? We have new doors with full length windows with the white trim. Yes we did. Just apply the stain as usual. With this door the trim was a light tan color.

For white trim an extra coat of stain might be needed. I have a PlastPro fiberglass sidelight and the stained insert only has peeled off three times since its install in I prepped properly and used a PlastPro Stain Kit each time. They offered me a Stain Mate spray to use that will make it stainable. Paintable and stainable is the same thing. Most likely it is a non-paintable plastic insert.

If they the manufacture have a primer the Stain Mate in question? You could try a different stain, like Old Masters gel stain, and see if that sticks. Otherwise, you will need to prime the fiberglass before staining. Finding a primer that will stick could be a challenge. I had some fiberglass French doors installed in my back porch which is roofed so the doors are not in direct sun.

Do I need to give them more coats? If so, how many? Do I have to coat the inside? Thank you in advance for your help. Esther Maria. You should re-apply when you notice the sheen dulling. You can also varnish the interior side is wanted, 1 coat would be enough as long as it looks good. This could help with cleaning but not really necessary.

Hello, I have a new fibreglass exterior front door. It is a smooth finish. I have applied one coat of gel stain and I have done a wood grain faux finish. It is possible to apply another coat of stain but this will make the background more opaque. Try a they thin coat to see how it goes. Make sure the stain is fully dry and hard before applying another coat as it could lift the previous coat of stain.

We are refinishing our fiberglass front door. It is the original door and has been refinished before. We are going to use Gel Stain from Minwax. We have sanded the wood trim down. Could we use the Minwax Gel Stain on the wood trim? You can use the same gel stain if the wood frame and trim is raw, unstained or not painted.

If it is painted you can still use the gel stain but a neutral tan background color is needed, satin sheen paint. Also, you would need to replicate the wood grain with the stain.

Of course, the frame can be painted either the common house trim color or an accent that looks good with the stained door. I have gel stained a fiberglass door and I also have spar urethane. I read that spar urethane is for wood but can it also be used as a top coat on my gel stained fiberglass? Spar urethane finishes is a great finish that can be used over gel stains and on fiberglass doors. Hello, I ordered a Thermatru door, and I asked to be stained inside and primed outside.

My intention was to paint the outside. Now I had a change of mind, and want to stain the outside also. Can I stain the outside to give it an wood finish? Do I need to remove the primer if I want it stained? No need to strip off the primer. Stain over it with a gel stain or wiping stain Old Masters is the best stains.

If a tan background color is needed use a satin sheen oil base paint tan color before staining. The paint will provide a nice background color for the stain. I work for a fiberglass door manufacturer name Nova Doors and we use a water based product called TruCoat for painting and staining our fiberglass doors.

I have a thermatru door that was scratched when I had a refrigerator installed, what kind of filler should I use on the scratches. It will show when stained or painted.

With Gel Stain Application On Fiberglass Door Free that said, use a stainable wood filler. Try to apply only to the scratch and carefully sand when dry. You can also try to add matching texture to the filler when it is still wet using a tooth pick, draw lines the match the wood texture.

It is suggested to stain a fiberglass door while it is installed to minimize handling and that only the lock set should be removed. How do you allow for drying time? How to you secure your home if painting the front door? How do have time for staining, drying, sealing and drying again?

Brainerd Soft Close Cabinet Door Damper Online Small Wood Carving Chainsaw Kit Wood Carving Machine Bunnings For Sale Home Cnc Machines For Wood Zero