Hello, I ordered a Thermatru door, and I asked to be stained inside and primed outside. My preference when staining a fiberglass door is the vertical position and on the frame. The Helmsman spar will work well. October 22, at pm. I prefer to apply the oil based gel stain with a good bristle brush gel stain application on fiberglass door out blend one section into another with the same brush.

Brush Application Apply a thin first coat so it just wets the surface. Quickly work the brush into the grained texture. Apply the finish in the same order as when staining. Observe the door for any runs or drips and quickly correct with the brush. Do not over brush. Over brushing could loosen and lift the stain.

If this occurs, wait until the finish is dry then gently wipe the area with a tack cloth to remove any balls of stain and finish. Carefully repair any damaged stain with a small brush then recoat the area before proceeding with the next coat. Allow the first coat to thoroughly dry then apply another coat in the same order. Three coats are recommended for the best protection.

After filling and priming the sprayer test the sprayer pattern, pressure and volume on a piece of cardboard or plywood. Apply the topcoat in a sweeping motion, first in one direction and then in the opposite direction. Avoid spraying a heavy coat as drips or runs can occur, correct drips with a brush before the coat is dry. Allow the first coat to dry before proceeding with the following coats. The second application needs to be sprayed the same as the first.

Follow with one, or more, coats sprayed in one direction only. We have a wood grain fiberglass door that has been painted white. Can this door be stained with a gel stain so that it will look like a wood door? And if so, how would I do this? This will be the background color for the gel stain. Now stain and finish as usual. Be careful to choose a fiberglass safe paint stripper. I want to use gel stain on my fiberglass wood grain door the molding is a primed from Factory can I use the gel on the primed Factory molding and what kind of oil should I use?

Yes a gel stain can go over the primed molding. Any good gel stain will work, Old Masters is a good brand. Do we have to use a clear coat?

Or can we just use the stain? A clear coat must be used over the stain. Gel or wood stain alone has very little protective power and must be protected from the elements with a suitable clear coat. Yes, they are the same thing. Varnish, polyurethane, etc are all suitable clear coats that can be used on top of a stain. After staining and applying top coat, my husband noticed that the stain was darker on one side than the other.

Can I put another coat of stain on top of top coat to darken the door? Yes, a second is possible. Make sure to wait for the first coat to dry completely, typically several hours or overnight. If you apply the second coat to soon it could reactivate the first coat smearing it around. I need to strip the stain and top coat to restrain my 3 year old fiberglass door. I used gel stain and a polyurethane topcoat over factory base.

What is the best product and process to use to strip topcoat and stain? Klean-Strip Fiberglass Paint Stripper is one of the best and is fiberglass safe. Finish up with a washing with plain water. You might need to use Lacquer Thinner after the washing to remove some stubborn spots. Do you recommend one or two coats of stain? I just worry that with 2 coats it may just look painted.

Is one coat durable enough with the urethane coat? Thanks Tiffany. More than one coat of stain is just about the look. You can use as many coats as you feel is needed to get the look your after. I would do two coats of urethane for a more durable finish. What type of urethane would you recommend over a fiberglass door with gel stain finish? The Helmsman spar will work well. I would stick with an oil base product for its ease of application but waterborne urethanes also will work, make sure what is used is recommended for exterior use.

Is it possible to get a light oak finish over the tan base of a fiberglass door, or will I have to prime it in a buff tone? Seems that mid tone and darker gel stains are all that I am seeing applied successfully. Also, does the interior side require a top coat? The light oak color is very difficult to achieve over typical dark tan fiberglass. The buff color will be needed. Try to choose an eggshell sheened oil base paint if available, easier to stain over.

Plus Old Masters makes the best gel stains, in my opinion. The lower section of our fiberglass door was weathered. I use a wiping stain instead of a gel stain. Color is fine but not sure what else to do or if I have to remove???

All you need t do now is apply a clear coat to protect the new stain color from the elements. Any exterior rated finish will work; varnish, polyurethane or water based acrylic. I have tried re-applying, using a touch up stain Gel Stain Application On Fiberglass Door Test marker, with no success. Is there a touch up product for scratches on a fiberglass door? It is possible the scratches are into and damaged the embossing wood grain. It is impossible to fix this type of damage.

Try an artist brush and the gel stain, carefully apply to the scratch only and reapply when dry if needed. I have a thermatru wood grain front door that is under a porch roof, never receives sun or rain and the original mahogany colored gel stain was never top coated.

To refinished this door I cleaned the inside and outside door with lemon pine sol as I read that this product did not require a rinse and did not leave a residue. Then my painter simply restained the door with dark mahogany Zar oil based interior wood stain. One coat. The door is beautiful. My question is must I top coat? I would prefer not to because I may need to reapply another coat of stain and did not want to get involved with taking off the top coat.

How long would this finish last without a top coat? You should get a couple good years out of the new stain before recoating. Just put the top coat on yesterday. It looked beautiful with just stain. Can this be fixed? Need a little info; What top coat was used, how was it applied and what was the weather conditions? Plus, is the door finish cloudy? This will help figure out what happened and how best to fix.

It was the Therma Tru top coat that came with the Therma Tru stain. It was brushed on. The weather was mid eighties, clear.

The door finish is not cloudy. It was beautiful. The top coat turned cloudy within an hour after applying it. If I remember correctly this finish is a water based exterior acrylic urethane. Brushing is very difficult with this finish, dries too quickly. Applying it too thick could cause this problem. This is a very helpful thread. I have a Jeld-Wen patio door fir texture that I need to stain. I need to test some colors on fiberglass to be sure I have a good match but there was no sample included with the door.

I wrote to Jeld-wen but have not been able to get a response. Is there a way to get a sample of fiberglass from some other source to test my stains? Can I test them on a different surface, like a board painted to match the base color of the door? Also, what do you recommend for a durable, long lasting outdoor top coat?

Thank you. Using a painted board is your best bet. It is probably the toughest exterior clear coat you can get. I had the glass replaced in my fiberglass door and need to know how to stain plastic glasss trim to match stained door.

This is on the interior side as we had exterior painted. First you need to prime the plastic trim then paint it a medium tan color, this will match the original color of the door. Could also use a tinted primer, ask you local paint store if they can tint it to a tan color.

Now you need some gel stain or heavy bodied wiping stain that matches or comes close to the door stain color. Application is by brush, might take more than one coat. Protect the rest of the door with blue painters tape and masking paper or news paper. After the stain is applied and dry apply a coat or 2 of sealer, polyurethane or varnish. Might be a good time to re-coat the entire door. I just had a ThermaTru fiberglass entry door installed.

I painted the outside to avoid the weathering of stain. However, I wanted the wood look inside, so I stained it and the sidelights with Varathane gel stain, Ipswich Pine color, two coats. It looks beautiful now, before I have topcoated. I see someone commented that the inside needs to have a topcoat. Please advise as to reasons for top coating the inside.

A clear coat will protect the stain from fading and damage. Applying a clear coat, varnish or poly, can be a challenge but careful and apply only thin coats problems can be minimized. I would choose an oil base finish, fast drying polyurethane is good.

Water based finished can present problems as they dry too fast and are harder to apply by hand. I have just had a therma-try door installed. I stained both sides of the door yesterday afternoon and it came out nicely, other than having to pluck hairs off from the brush supplied with the Therma-try recommended Same Day Stain Kit.

Do I need to remove more, even though the door looks good, or will it eventually dry. If I let it go too long without putting on the top coat will there be a problem? Thank You! Let it dry. With high humidity and somewhat low temps it could take a few days. Using a high quality natural bristle brush, spread a thin, even coat over the entire surface, starting with the raised panel sections.

Always make final brush strokes in the direction of the embossed grain. Areas of heavier coats should be evened out before moving to a new section. To darken the color, apply additional coats by following the instructions above. Let the stain dry 6 to 8 hours between coats. The painter followed the grain to make the door look like it is made of stained wood.

He started with the outside, then stained the inside. Before applying a clear finish, test the stain for dryness by wiping a small hidden area with a rag moistened with mineral spirits. If the last coat of stain can be removed with mineral spirits, do not apply a clear protective finish.

Wait until the stain is completely dry. Allow the finish to dry at least 6 hours before installing or closing the door to avoid sticking. For exterior applications, apply a coat of clear protective finish every months to keep the door looking beautiful. So, here is the front door the next day. Place the door in a well-ventilated, covered workspace.

Remove any hardware with a screwdriver and set it in a safe place, then place the door on a solid work surface. Wet a clean rag with mineral spirits and wipe down the entire surface of the door. Dirt, dust and grime can make the gel stain apply unevenly or not adhere properly to the door, resulting in splotches and streaks. Let the door air dry for 20 to 30 minutes, then cover any areas that you will not be staining with quality painter's tape.

If the door has a glass insert, cover it with plastic wrap and secure it with tape. Open a can of gel stain and mix it thoroughly with a stir stick.

Starting with any raised areas, apply the product evenly to the fiberglass door with a natural-bristle paintbrush.

Electric Wood Carver Uk 95 Kreg Rip Cut Parts 91 Wood Work Designs For Tv Cabinet Guide