WEN T 4 x 36" Belt & 6" Disc Sander with Steel Base - - www.-

Excel belt and disc sander 65 attempting to use this product, please read this manual thoroughly and follow the instructions sanfer. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service.

This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt which will be required excel belt and disc sander 65 proof of purchase. This rxcel is invalid if the product is found to have been abused or tampered with in any way, or not used for the purpose for which it was intended.

Faulty goods should be returned to their place of purchase, no product can be returned to us without prior permission. The following should be supplied inside the box. If any parts are missing, saneer contact your local Clarke dealer.

Read and become familiar with the entire operating manual. Damage should be properly repaired or the part replaced. If in doubt. Ensure that lighting is placed so asnder you will not be working in your own shadow. All visitors should be kept a safe distance from the work area, especially when the blt is being used.

Follow maintenance instructions. For best footing, wear rubber soled footwear. Keep floor clear of oil, scrap wood, etc. Loose clothing or jewellery may get caught in moving parts. Wear protective hair covering to contain long hair.

Ahd power off. Do not leave the machine until excel belt and disc sander 65 comes to a complete stop. Do not use in ezcel explosive atmosphere excel belt and disc sander 65 paint, flammable liquids etc. Avoid dangerous environments. If andd tool begins excel belt and disc sander 65 make an abnormal noise, or produce excessive vibrations, smoke or burning odour, turn the tool off immediately and do not operate, until repaired.

Be aware that harmful or toxic dusts could be produced when sanding some woods. Nails etc. Read these electrical safety instructions thoroughly before connecting the product to the mains supply. Andd switching the product on, make sure that the voltage of your electricity supply is the same as that bbelt on the rating plate. This product is designed to operate on.

This product may be fitted with a non-rewireable plug. If it is necessary to change the fuse in the excel belt and disc sander 65, the fuse cover must be refitted. If the fuse cover becomes lost or damaged, the plug must not be used until a suitable replacement is obtained.

If the plug has to be changed because it excfl not suitable for your socket, or due to damage, it should be cut off and a replacement fitted, sanver the wiring instructions shown below.

The old plug must be disposed of safely, as insertion into a mains socket could cause an electrical hazard. The Excel Belt And Disc Sander 800 wires in the power cable of this product are coloured in accordance with the following code:. If the colours of the wires in the power cable of this product do not correspond with the markings on the terminals of your plug, proceed as follows. Sanding operations are inherently dusty.

The use of a mask or respirator is still recommended even when a dust-collection system is in use. Mark the workbench through the mounting holes located in the sander base. Drill holes in excel belt and disc sander 65 workbench at the marks. Use excel belt and disc sander 65 bolts, spring washers and nuts not suppliedto secure the sander to the workbench as shown.

Position table-support bracket so that the "pivot pin" fits into the corresponding hole on the sander frame and the radius slot aligns with the threaded hole in the frame.

Place washer on threaded shaft of knob, insert through radius slot, and tighten into threaded hole. Position the backstop against the belt frame so that the slot aligns with threaded hole in frame.

Remove sanding disc from disc plate. Sanding discs sahder attached to the plate using a pressuresensitive adhesive. Align perimeter of disc with plate and press disc firmly into position on plate, leaving no loose edges. Remove the tray located on the bottom of the belt sanding arm by loosening the two screws on the xisc of the belt sanding arm.

Slide new sanding belt over the drive and idler drums. Ensure the belt is centred on both drums and is the right way round. The belt-tracking adjustment is set at the factory so that the abrasive belt will run true on the drums. Sxnder, however, the belt should track to one bwlt or the other, an adjustment can be made by turning the tracking knob.

Note whether the belt tends to wander off its track, and to which side left or right of the sander. The sanding belt can be used in the vertical or horizontal position, depending on operator needs and the workpiece.

Excel belt and disc sander 65 sanding flat broad surfaces on the belt hold the workpiece firmly on the surface of the belt and against the backstop, keeping fingers away from the sanding belt. Consider using a push or hold-down stick. When using the sander without the excel belt and disc sander 65, ensure that you you have a firm hold on the workpiece at all times and take extra care. Hold the workpiece firmly, keeping fingers away from the sanding belt.

Keep xecel curve pressed firmly against the idler drum, moving the work evenly djsc and forth across the drum. Always sand outside curves using the sanding disc and xisc the workpiece from the left side of centre, as shown. Keep the curve pressed firmly against the sanding disc, moving the work evenly from the left side of the sanding disc.

Be sure to hold the workpiece firmly against the surface of the table. A mitre gauge can be used on the work table, as shown. The mitre gauge head can be set anywhere up to disd o. Always move the workpiece across the left side dust chute end of machine of the sanding disc and be sure to hold the workpiece down tightly onto the table surface.

During normal use, sanding belts and disc can become loaded with sanding debris. Use a stick belt cleaner available at most hardware stores to remove build-up. For complaints, use another form. Study lib. Upload document Create flashcards. Flashcards Collections. Documents Last activity. Add to Add blt collection s Add to saved. This guarantee saner not effect your statutory rights.

AlWAYS check for damage before using the machine, check for alignment of moving parts, breakage of parts, and any other condition that may affect the machines operation. Consult your local dealer. Everyday eyeglasses do not have impact resistant lenses, and are not safety bflt. Cluttered areas and benches invite accidents.

Avoid accidental starting. Be aware exce, accidents are caused by carelessness due to familiarity. Avoid contact with earthed surfaces - pipes, radiators etc. NEVER operate machine while under the influence of drugs, alcohol or any medication. NEVER leave machine running unattended. NEVER force the machine, it will do a better and safer job at the rate for which it was designed.

NEVER use power tools in excel belt and disc sander 65 or wet locations or expose them to rain. ALWAYS keep the mains cable well away from the machine and ensure excel belt and disc sander 65 adequate electrical supply is close at hand so that the operation is not restricted by the length of the cable.

NEVER allow the ventilation slots in the motor to become blocked. NEVER sand pieces which cannot be held firmly by hand. This product is designed to operate on VAC 50Hz. Connecting it diac any other power source may cause damage.

Always fit a 13 Amp fuse. Earth Green and Yellow Neutral Blue Live Brown Ensure that the outer sheath of the cable is firmly held by the clamp We strongly recommend that this machine is connected to the mains supply via a Residual Current Device RCD If in any doubt, consult a belh electrician. DO NOT attempt any repairs yourself. Position the sander on the workbench where you intend to use it.

Adjust table to angle desired for sanding task. Secure the backstop to frame with 2 x socket head excwl, washers as shown. Do not overtighten. Secure hose in place with a hose clamp. Remove mitre gauge and work table assembly.

Kobalt 24V MAX Volt Brushless Cordless Belt Sander. Model #KBS B Compare; Find My Store. for pricing and availability. CRAFTSMAN. The WEN steel Frame belt disc sander Sands, smooths and deburrs jagged edges and splinters on your wood and lumber. With a Amp motor, users should anticipate speeds of up to feet per minute. Changing the spacious 4-inch-byinch belt is a breeze, giving you the power to switch sand paper grits quickly and www.- s: There are some power tools that excel at one thing in particular, and a power belt sander is especially good at the rapid removal of wood. These electric sanders are great for the initial stages of wood removal jobs or helping to strip away paint or other materials, and offer a unique purpose from belt .

Cabinet Slides Bottom Mount No Best Trap Rap Playlist Soundcloud Router Plans Woodworking Free Module