Drill Master User Manuals Download | ManualsLib

If you are unable to print this document, turn off your printer for at least 15 seconds and try again. Get advanced printer help. Visit Adobe Support for instructions in troubleshooting common printer problems. A simple jig, a special drill bit, and a self-tapping screw work together to create a quick yet very strong joint. When it comes to woodworking techniques, it doesnt get much simpler than this basically just butt joints that are screwed together.

But the screws arent sunk straight through the workpieces like they normally would be. Instead, theyre set at a slight angle This means the screw enters the face of one piece and bites into the edge of the mating piece, as indicated in the photo drill master pocket hole jig manual id. It doesnt take long to see the benefits to this.

Since these are butt joints, cutting pieces to length requires almost no math. You dont have to add or subtract the lengths of any tenons or allow for the depths of dadoes, grooves, or rabbets.

Just measure, mark, and cut. Creating the joint is fast too. Thats because there are just two steps. First you drill the holes. Then you screw the pieces together. The only clamping that may be required is to keep the pieces from shifting while youre driving the screws.

And if you reinforce the joint with glue, theres no waiting for it to set. As soon as the screws are in place, you can move on to the next joint.

Sound simple enough? It is. But like any method of joinery, you need to have the right tools on hand in order to work quickly and efficiently. This means you have to have a pocket hole jig. As you can see in the photo on page 2, there are a number of pocket hole. But they all do exactly the same thing: guide the drill bit so it will drill an accurate drill master pocket hole jig manual id exactly 15 into the face of a workpiece, as in Fig.

Thats all there is to it. But theres more to pocket hole joinery than just a jig. Youll also want to have the right drill bit. It makes the job much quicker and the pocket holes more consistent.

Whats unique about this special bit is that it drills two holes at once. The part you see, the oval-shaped counterbore, holds the head of the screw. Its just deep enough to put the head below the face of the workpiece. The second hole is for the. Okay, you know what the bit does, but how does it drill both holes at the same time? I drill master pocket hole jig manual id the bits with square steps or shoulders not the tapered ones.

This way, the head of the screw has something solid to stop against, and theres less chance it will try to drive in farther. Of course, the holes have to be drilled at a consistent depth in the first place.

So you need to have a stop collar for the drill bit. Not all come with them. And to set this collar, you need to know where the hole should stop.

I like the bit to stop so the shank hole ends up just short of the edge of the workpiece, as shown in Fig. If you drill completely through the piece, the wood usually splinters, which may prevent the two pieces from fitting together tight. When drilling the pocket holes, I like to use a corded, electric drill. It has more power and speed than a cordless drill, which is pretty helpful when drilling drill master pocket hole jig manual id hardwoods.

Plus, you wont have to worry about running down the battery with repeated use. As far as the drilling goes, thats about it. But there are a couple more things to mention. First, you need to decide which workpiece to drill the pocket in. I like to think of the screws as if they were tenons or tongues, if Im working with plywood panels.

So the piece Id normally cut the tenon on is usually the one that drill master pocket hole jig manual id the pocket holes. Most times, this means the screw threads are cutting into edge or cross grain which is much stronger than if the screws were being driven into end grain. However, this isnt an unbreakable rule. In the Sectional Enter-tainment Center plan, I often drove the screws into the edge of a plywood panel rather than into the edge grain of the frame around it because I was able to hide the screws better.

In other words, when the jig is aligned. But youll have to adjust the position of the jig on the piece and. There can be a bit of trial Drill Master Portable Pocket Hole Jig Manual Ti and error here, and to check the setup, just run a drill master pocket hole jig manual id through a test piece to see where it exits and how far.

As you can see in the photo, there are at least a half dozen available, and youll find them just about everywhere. But when comparing the costs, make sure you know what youre getting and what youre not.

When choosing a jig, there is really just one essential: hardened guides. Most jigs do have them, but not all. And I found the positioning stop on the end of the Kreg Rocket and some of the other jigs to be helpful.

As far as being able to adjust the width between guides, its often just as easy to reposition the jig. Finding the right drill From Woodsmith Magazine.

The stop collar ensures consistent results. I liked bits with square shoulders instead of tapered. Plus youll need a stop collar for the bit. Besides these two. More on all drill master pocket hole jig manual id beginning on page 3. Plus, Kreg sells a face clamp thats pretty handy. Assembly As soon as the holes have been drilled, youre halfway to a strong pocket hole joint.

The second step is to screw the workpieces together. This is just about as easy as it sounds, but again, there are some important differences from the way youre used to working with woodscrews. The first big difference is the screws that are used. Instead of regular woodscrews, pocket hole joinery uses self-tapping screws, as you can see in the margin drawing below.

These have an auger point, which allows them to drive into the mating workpiece without splitting the wood. Because these screws are self-tapping, youll want to match the threads on the screws with the type of material youre using. But dont worry. The big decision is whether to choose fine or coarse threads.

Theyre concern for softwoods and plywood. However, with softer woods, like cedar, you need to watch that you dont drill master pocket hole jig manual id the screws in too far. This is a real possibility even with the square shoulder of the counterbore and the panhead on the screw. The way to prevent driving the screws in too far is to use a drill with drill master pocket hole jig manual id clutch.

This time, I use a cordless drill. You can play with the setting, but with softwoods, its going to be fairly light. If you dont have a drill with a clutch, you might want to drive the screws in most of the way and then finish them with a screwdriver.

Besides a drill with a clutch, you will also need a long driver. The pocket hole screws I used. You can get by with a 3"-long driver and anyway, its a good idea to have one on hand when you need to get into a tight cornerbut drill master pocket hole jig manual id find that a 6"-long driver is much easier to work with.

It lets you drive the pocket screws in at the shallow 15 angle and still have enough clearance for the chuck of the drill. When youre ready to screw the two pieces together, the important thing Drill Master Pocket Hole Jig Manual Us is to make sure theyre not going to shift during assembly.

Remember, the shank hole is a smaller diameter than the threads of the screw, and its not drilled completely through the first piece. So the two pieces will want to pull apart slightly as the threads of the screw start to engage the mating piece. For face frames and other flat assemblies, I came up with this plywood platform.

Two short fences position the workpieces 90 to each other, and to help keep the pieces from shifting while the screws are being driven, I placed strips of adhesive-backed sandpaper across the base. The screws will pull the joint back tight, but sometimes, the pieces will have shifted slightly so that theres a small shoulder between them.

There are a couple of ways to prevent the workpieces from shifting. Kreg offers a face clamp that has a large, flat disc welded to one of the pads, refer to the main photo on page 1.

This disc is positioned across the outside faces of the workpieces to hold them flush. This doesnt actually keep them from separating.

Dec 31,  · How to use the Drill Master Portable Pocket Hole Jig Kit. I purchased mine at Harbor Freight www.- Jul 31,  · Harbor Freight pocket hole jig tool review. Item so far I have used it to make one project and it did great! Curious to know what I am missing from the. Choose the distance desired between the pocket holes and use the ruler on top of the fixed L Base (2) to adjust the workpiece as needed in the Pocket Hole Jig. The Bushings (2) on the Drill Guides (4,5) are intended for different size materials. For materials /4” and 1 .

Cam Lock For Cabinets Yoga Flattening Jointer Plane Sole 90 Best Rap Walkout Songs In China Tra001 Parts Youtube