A countersink (symbol: ⌵) is a conical hole cut into a manufactured object, or the cutter used to cut such a hole. A common use is to allow the head of a countersunk bolt, screw or rivet, when placed in the hole, to sit flush with or below the surface of the surrounding material (by comparison, a counterbore makes a flat-bottomed hole that might be used with a socket-head capscrew). A countersink may also be used to remove the burr left from a drilling or tapping operation thereby improving the finish. 2 countersink bit. 1) Техника: зенковочная шарошка, зенкер (металлорежущий инструмент для обработки цилиндрических отверстий и их фасонных участков), зенковка (режущий инструмент для получения конических углублений или снятия фаски у торцевой части предварительно образованных отверстий). 2) Макаров: раззенковка.  countersink bit — noun a bit for enlarging the upper part of a hole • Syn: ↑counterbore, ↑countersink • Hypernyms: ↑bit Useful english dictionary. More than countersink bits at pleasant prices up to 17 USD Fast and free worldwide shipping! Frequent special offers and discounts up to 70% off for all products!.

A common use is to allow the head of a countersunk bolt, screw or rivet, when placed in the hole, to sit flush with or below the surface of the surrounding material by comparison, a counterbore makes a flat-bottomed hole that might be used with a socket-head capscrew.

A countersink may also be used to remove the burr left from a drilling or tapping operation thereby improving the finish of the product and removing any hazardous sharp edges. The basic geometry of a countersink cutter inherently can be applied to the plunging applications described above axial feed only and also to other milling applications sideways traversal. Therefore, countersinks overlap in form, function, and sometimes name with chamfering endmills endmills with angled tips. Regardless of the name given to the cutter, the surface being generated may be a conical chamfer plunging applications or a beveled corner for the intersection of two planes traversing applications.

A countersink may be used in many tools, such countersink bits menards drillsdrill pressesmilling machinesand countersink bits menards. A Dan Martin Style "zero flute" countersink is a cone-shaped tool with a cutting edge provided by a hole countersink bits menards goes through the side of the cone.

The intersection of the hole and cone form the cutting edge on the tool. The cone is not truly symmetrical as it is essential that the cone retreats away from the cutting edge as the tool rotates providing clearance. If this does not occur the cutting edge will lack clearance and rub rather than bite into the material.

This clearance is referred to as cutting relief. These tools are best used as deburring tools, where the burr from a previous machining operation needs to be removed for cosmetic and safety reasons, however they may be used in softer materials such as wood or plastic to create a countersunk hole for a screw. The fluted countersink cutter is used to provide a heavy chamfer in the entrance to a drilled hole. This may be required to allow the correct seating for a countersunk-head screw or to provide the lead in countersink bits menards a second machining operation such as tapping.

A back countersinkalso known as an inserted countersinkis a two piece countersink countersink bits menards on tough to reach areas. One component is a rod that is inserted into countersink bits menards existing hole in the workpieces; the other component is the cutter, which is attached to the rod, or extends out of it, after it is in position.

The common theme is accomplishing machining operations on the far side of the workpiece from the spindle face, which obviates a "second operation" setup. This reduces setup time and frustration in several ways. Not only does it obviate the flipping over, cleaning, reclamping, etc. It can often be difficult to avoid chatter also known as machining vibrations when cutting with countersink cutters. As usual in machining, the shorter and more rigid the setup, the better.

Better-quality fluted countersink cutters sometimes have the flutes or at least one flute at an irregular pitching. This variation in pitching reduces the chance of the cutting edges setting up a harmonic action and leaving an undulated surface. This surface ripple is also dependent on the surface speed of the cutting edges, material type, and applied pressure or feed rate ; once started it is hard to remove.

Too light Neiko Countersink Bits a feed tends to increase chatter risk. As in many other machining operations, an appropriate response to the chatter countersink bits menards be to decrease speed and increase feed. On a drill press, the slowest countersink bits menards spindle speed countersink bits menards usually best. With a variable-speed handheld countersink bits menards drill, the trigger is best squeezed lightly to yield a low spindle speed.

Good chatter-free results can usually be had by countersinking by hand as opposed to running the tool in a powered spindle. The slow speed and sensitive feed tend to prevent chatter. With a quarter-inch-hex shank, the countersink cutter can be held with a screwdriver handle of the indexable - bit type. Form countersinking, also known as dimplingis a countersink that is formed into sheet metal to increase the strength of a structure as the countersinks of multiple pieces nest together.

There are two processes for producing formed countersinks: coin dimpling and modified radius dimpling. This style of construction is often countersink bits menards in modern household appliance design, because it allows the product to be lower-priced, and the quality can still be good as long as the sheet is thick enough.

From Wikipedia, the free encyclopedia. This article needs additional citations for verification. Countersink bits menards help improve this countersink bits menards by adding citations to reliable sources. Unsourced material may be challenged and removed. Cross-sections of countersunk holes of various chamfer angles. Cutting and abrasive tools.

History Glossary Wood lumber. Frame and panel Frameless construction. Category WikiProject Commons. Categories : Metalworking cutting tools Metalworking terminology Woodworking hand tools. Hidden categories: Articles needing additional references from November All articles needing additional references. Namespaces Article Talk. Views Read Edit View history. Help Learn to edit Community portal Recent changes Upload file.

Download as PDF Printable version. Wikimedia Commons.

Drill Bits & Accessories Montana Brand® Black Oxide #6 Replacement Countersink with 3/32" Drill Bit Model Number: MB Menards ® SKU: Mar 17,  · Menards is a family-owned home improvement retail chain with more than locations, primarily in the Midwest. Their slogan, “Save Big Money!” is legendary. And their employees will tell you there are ways to save big money that not everyone knows about. A countersink (symbol: ⌵) is a conical hole cut into a manufactured object, or the cutter used to cut such a hole. A common use is to allow the head of a countersunk bolt, screw or rivet, when placed in the hole, to sit flush with or below the surface of the surrounding material (by comparison, a counterbore makes a flat-bottomed hole that might be used with a socket-head capscrew).

Sign Lettering Router Bits Value Small Simple Wood Projects Design