Slides movement describes exactly cabinet drawer slide removal factor the slide operates inside of the cabinet. RedRyder last month. Remove the drawer from the cabinet and place it on a flat surface. Typically, drawers use 8 stabilizer screws, which will require a Phillips-head screwdriver. Stand in front of the piece of furniture and slide the drawer open as far as you slkde, with one hand on each side of the drawer.

In some cases, the drawers in your furniture will have stabilizer screws, which add an extra step to the drawer-removal process. Even so, these drawers and screws come out relatively easily. Just follow the steps below:. Be sure to work on the drawers in the proper order, by starting at the top and moving down drawer by drawer.

This can result in an unstable piece of furniture that can wobble or tip over. Stand in front of the furniture, and leave enough space for the drawer to fully extend. Pull the drawer out as far as possible. Pull all the way until you feel the drawer hit its built-in stopping point. Find the stabilizer screws inside the body of the drawer. There should be two screws. Once you locate them, remove them with the proper screwdriver. Typically, drawers use 8 stabilizer screws, which will require a Phillips-head screwdriver.

Find the catch tabs, which should be on both sides of the drawer. Release the catch while pulling upward on both catch-tab mechanisms. You will probably need to pinch the catch tab with your thumb and index finger; this will release the drawer from both side tracks. Be careful because even if you emptied the drawer ahead of time, it can still be pretty heavy.

Also, once the drawer is removed, take a quick peek at the side of the drawer to see if there is any sort of number on it. This number will often be on a sticker or decal, and it indicates which opening in the furniture the drawer goes in. Number 1 is typically the top drawer, with subsequent numbers on each of the lower drawers.

Push the tracks back in before continuing to work on the piece of furniture. Using a straight, parallel motion, push the center stabilizer track in, along with both side suspension tracks. The drawers in anti-tip furniture have cables attached to them that prevent multiple drawers from being opened at the same time. This helps to keep the furniture from falling over or becoming unsteady—if multiple drawers are open, especially at the top, the piece can become top heavy and tip.

The anti-tip cables help remedy that but also add an extra step in the drawer-removal process. However, following these steps can make removing anti-tip drawers easy:. This helps to keep the weight at the bottom of the furniture. Always remove the top drawer first; it is the safest and easiest way to work on a piece of furniture. Stand in front of the furniture and make sure there is enough space for the drawer to fully slide out. Grab the front handle of the drawer, and extend it outward.

Pull out on the drawer until you feel resistance. Open the drawer completely, and you will be able to easily see the anti-tip cable, which will be attached to the rear exterior of the drawer. Use a screwdriver to unscrew it. Usually, the cable will be affixed to the drawer with a Phillips-head screw, so be sure you have a Phillips-head screwdriver handy.

Press and hold the disconnect tabs if your drawer has them. Examine the rear portion of the metal tracks on either side of the drawer. If you find a pair of adjustable tabs there, press both of them in at the same time to disengage them and allow the drawer to slide freely.

Make sure both tabs are pushed in completely. Slide the drawer straight off of its tracks. Pull the drawer towards you until it comes away from the piece of furniture. You may need to lift or angle the drawer upwards slightly in order to get it clear of the end of the tracks. Yes, you can buy them online or look for them in your local hardware or furniture stores. Not Helpful 2 Helpful 2. The drawers on my dresser have no visible rails and very little movement up or down.

Can you suggest an alternative method? I have an old Bombay Company dresser and I found that it had a peg in the back on both sides that needed to be pushed in. This may be the case for your dresser as well. Not Helpful 1 Helpful 6. Pull out the drawer to its fullest extent.

Hold the drawer front end with both hands and give a sharp lift up. The drawer will detach from the slides and can then be removed. To replace, fit the drawer onto the slides and push all the way in. Test correct operation by pulling out while supporting the drawer to make sure it halts on the stops. Not Helpful 5 Helpful 1.

Simply lock it back in place by riding it on the inside wheels of the supporters. If the drawer is defective, measure the drawer and find the model number for it to look for a replacement in places like Lowes or Home Depot. Not Helpful 6 Helpful 0. Line up the drawer with the track, check to see if it's lined up, and push forward.

Not Helpful 7 Helpful 0. Try using a putty knife to pry it. Pull it out as far as it will go, then slide the putty knife underneath. Not Helpful 0 Helpful 0. If you have the ball bearing gliders, there are levers on the sides of the drawers. Squeeze the levers and line the drawer up carefully. Once you start sliding the drawers back in, you will feel the levers click in place. Then, the drawers should easily glide for you!

Not Helpful 0 Helpful 1. If you have the ball bearing gliders and they are installed properly, including that they are the right size, they should glide all the way out. There are levers on each side that you squeeze and they will come out; unless they are worn out. Mine only opened an inch and I was able to pry them with a flathead screwdriver. The main thing that you need to be careful of when replacing them, is that they are lined up properly and level.

How do you remove drawer glides Cabinet Drawer Slide Removal Video if they are mounted Cabinet Drawer Slide Removal Example at the center of the drawer? After it stops when fully open, hold both sides, brace knees or foot against dresser and pull with firm, steady pressure on the drawer. It should slide right out. The glides are then accessible and can be screwed off. Not Helpful 1 Helpful 0.

Include your email address to get a message when this question is answered. When removing multiple drawers from a piece of furniture, always start with the top drawer and work your way down to prevent the piece from tipping over. Helpful 0 Not Helpful 0. Emptying the drawer of its contents before pulling it out will make it lighter and therefore easier to hold onto and maneuver.

It will also reduce your risk of injury if you happen to drop it. Submit a Tip All tip submissions are carefully reviewed before being published. Consider pulling on a pair of thick work gloves when working with metal drawers and tracks to protect yourself from cuts, pinches, and sharp edges.

Lightweight drawers can ordinarily be handled safely by one person. Related wikiHows How to. How to. More References We use cookies to make wikiHow great. By using our site, you agree to our cookie policy. Cookie Settings. Learn why people trust wikiHow. Download Article Explore this Article methods. Things You'll Need. Related Articles. Method 1 of All rights reserved. This image may not be used by other entities without the express written consent of wikiHow, Inc.

Unscrew the current slide hardware to remove the drawer. Pull out your drawer to locate the current slide hardware. Depending on the hardware, you might find the slides on the sides or bottom of your drawer.

Certain slides might have screws in the center of the hardware, as well. Remove the drawer from the cabinet and place it on a flat surface. To make your measurements simpler, turn the drawer upside down, so the bottom is facing up. Measure the length of the cabinet to have a sense of the furniture dimensions.

Use a tape measure to calculate the distance between the front edge of the open cabinet to the back wall. Examine the bottom of the drawer that you just removed. Extend the tape measure from the front edge of the drawer to the back edge. Take note of this measurement, as under-mounted slides need to be the exact same length as the drawer.

Kessel Lumber Products Keyser Wv Ar Blum Soft Close Cabinet Door Hinges Ve Buy 12 Table Saw