Woodworking By Hand

Woodworking Stack Exchange is a question and answer site for professional and amateur woodworkers. It only takes a minute to sign up. Connect and share knowledge woodworking projects using only hand tools 3nd a single location woodworking projects using only hand tools 3nd is structured and easy to search.

I currently do not own a woodworking projects using only hand tools 3nd saw or a band saw which is what I have seen typically used to resaw wood in half or to smaller dimensions. I would like to half a board to make a small box but only have a Japanese pull saw, a reciprocating saw, circular saw, a chop saw, and a hack saw.

Which tool would be best to accomplish this and keep the cut reasonably straight? Using the pull saw is my first guess but the board is about 5 feet long and I worry about deviating from the line on material that's about a half an inch thick.

I plan to plane down the material once it's sawed so I don't mind losing some of the waste material. Of the saws you list I think the pull saw is the best choice, in fact while it's theoretically possible to do it with one or two of the others doing it with the pull saw may be the only reasonable option. I should mention though, when comparing it should be done using a sharp, properly set rip saw on the Western end, and not a modern panel saw with general-purpose teeth which not infrequently is what the comparison is against.

A lot of this depends on you. There are some standard techniques that can help ensure a straight cut but just as with anything involving hand tools it usually requires practice to get good results some people have more of a knack for it than others. Fundamentally it starts with careful marking out and good sawing technique. You saw slowly letting the saw do the work and not forcing it, and deliberately not trying to saw fastand pause often as you go so that you can spot and correct for drift when it occurs.

Note these points are just as important for an experienced sawyer as for a beginner, so it's best to get into the habits early. And also you shouldn't expect to saw a board through in one operation start to finish, that's nearly never done woodworking projects using only hand tools 3nd resawing by hand. Instead expect to work in from both ends to meet up in the middle, repositioning the wood at least three or four times but frequently many more times than this.

Since most people tend to drift in the same direction try not to flip the board when doing this so that the drifts go in opposite directions. If you do drift off your line a fair bit the sawn faces will require quite a bit of planing to get them flat so you can loose quite a woodworking projects using only hand tools 3nd more thickness than intended.

You may want to factor this in to begin with by working to a greater thickness than eventually needed, or be flexible about the thickness of the stock you end up with. I hope these help get across the importance of having your work firmly held as you saw. While using a vice for this is one of the simplest and best ways it's not the only way so anyone without a vice don't despair, you can get creative with a few clamps if that's all you have.

But the work must be held firmly or you're setting yourself up for a world of trouble. Kerfing tool This is the way to 'cheat' on the experience of doing these cuts many times so you have become very good at it.

Using a kerf established around all four edges of a board is the number one way to guard against drift and a dedicated kerf-cutting tool is the best way to create those kerfs. Unfortunately it means you either have to buy a kerfing tool or kit or make one from scratch, but if you plan to resaw a lot by hand you may find it worth the money or effort. So far I haven't bitten the bullet and made one but it's woodworking projects using only hand tools 3nd my to-do list as resawing any significant length is proving challenging.

See previous Answer for more on resawing and the modern kerf-cutting tool, the kerfing plane: Creating additional boards from thick lumber. Some further outside links with much more useful information, pics and video on resawing by hand: Resawing By Hand on Close Grain. Resawing again — Problems and Solutions on Bob Easton's blog.

Resawing a board by hand from Badger Woodworks. As you can see, all three of the above emphasise the importance of flipping the board frequently. There's a good chance your generic "Japanese pull saw" is sharpened for crosscutting and while it can do the job it'll labour, particularly in fibrous woods. Sign up to join this community. The best answers are voted up and rise to the top.

Stack Overflow for Teams — Collaborate and share knowledge with a private group. Create a free Team What is Teams? Learn more. How can I resaw material using only hand tools? Ask Question. Asked 4 years, 1 month ago. Active 2 years, 1 month ago.

Viewed 3k times. Improve this woodworking projects using only hand tools 3nd. SaSSafraS 5, 6 6 silver woodworking projects using only hand tools 3nd 21 21 bronze badges. Add a comment. Active Oldest Votes. Which tool would be best to accomplish this Of the saws you list I think the pull saw is the best choice, in fact while it's theoretically possible to do it with one or two of the others doing it with the pull saw may be the only reasonable option.

Some pics showing resawing in action: Bonus pics showing it being done with a ryoba: I hope these help get across the importance of having your work firmly held as you saw.

Detail pic of a ryoba showing the two types of teeth clearly: The larger triangular teeth are the rip teeth. See previous Answer for more on resawing and the modern kerf-cutting tool, the kerfing plane: Creating additional boards from thick lumber Some further outside links with much more useful information, pics and video on resawing by hand: Resawing By Hand on Close Grain.

Improve this answer. Graphus Graphus Thank you so much! I will definitely need practice but going at the cut from two directions had not occurred to me. I will definitely investigate the use of a kerfing tool also. I've made a couple of typos so when I correct those I'll edit in some more technique info.

Expect an updated version of the Answer later on today or first thing in the morning. Have you written any books, a blog or anything of the kind? I've learned a ton of useful things from reading your posts. Traditionally, another approach would be to use a froe to split off a thinner board.

But that doesn't work well unless the grain is going in the right direction, so it's woodworking projects using only hand tools 3nd more useful for lumber that was produced this way in the first place, or that was riftsawn. Show 5 more comments. Sign up or log in Sign up using Google.

Sign up using Facebook. Sign up using Email and Password. Post as a guest Name. Email Required, but never shown. Featured on Meta. Stack Overflow for Teams is now free for up to 50 users, forever.

State of the Stack Q1 Blog Post. Linked Related Hot Network Questions. Question feed. Woodworking Stack Exchange works best with JavaScript enabled.

If you’re looking for woodworking projects to get stuck in to, then don’t forget to check out our Premium Video Series. We show the approach to woodworking from a minimal, hand tool perspective. Watch in detail online, as we take you step by step through the projects. Browse Our Premium Woodworking Projects . Aug 26,  · Things like squares, bench hooks, shooting boards, marking gauges, storage cabinets etc are great projects where you can stretch your hand tool muscles and not have to worry about messing up unique and expensive lumber. Plus once finished these project give back every time you are in the shop The Hand Tool School is Open for Business! Aug 19,  · A complete beginner attempts to learn the traditional methods of wood work and Woodworking techniques using only hand tools. Woodworking By Hand A complete beginner's attempts to learn the traditional methods of Woodworking using only hand tools. Labels: Hand Tools, Projects. Friday, 3 August Happy Birthday To Me 2.

Fine Woodworking Coffee Table Join Mirka Deros Sander Review Inc Square Tool For Woodworking Pdf