Warm up with these basic recommendations and rules of thumb. Christchurch Phone 03 Email Stais. It is left to dry and then buffed prior to the polyurethane being applied. We stain the timber, rather than add a tint to the polyurethane. Wood is a natural product which expands and contracts in reaction to the amount of moisture in its environment.

We can also undertake minor or major repairs and renovate old floors — see Recoating, Renovations and Repairs. We use specially designed German commercial floor sanding machines and only the very best products available, to ensure a top quality result. Should your floor require repairs, these will be done first. Any nails will be punched in and gaps filled. Solid timber floors can be fully sanded and recoated four to five times and engineered floors, three to four times.

The floor will be sanded, using a number of different grades of sandpaper. There will be considerable dust during this process and while our sanding machines have bags to collect the majority of the dust and these are used in conjunction with industrial vacuum cleaners , please expect some dust to escape into your home. Obviously, we will try to keep this to a minimum. Should you wish to alter the colour of your timber, we can darken or lighten your floor through stains. These would be applied at this stage — the selection of stains is best viewed at our showroom.

Staining is a specialist process; they are thin, highly absorbent liquids that have to be applied at speed in order to create uniformity. We stain the timber, rather than add a tint to the polyurethane. Tinting polyurethane can result in a patchy floor as the polyurethane in high use areas becomes worn over time. It is important to remember that a stained timber becomes richer once the coating is applied and the number of coats applied is determined by the depth of the colour chosen.

Staining is a time consuming process and needs to be considered at the time of quoting, rather than a last minute addition. Inconsistencies in existing floors, such as floors made from differing timber species, timbers of different ages or where there are vastly different wear levels, will not be completely masked by staining. Older timbers are more porous and appear darker, however dark stains can hide timber variations to a reasonable degree.

This is a process where we trowel fill the entire floor with a filler, in order to fill up any cracks and knots in the wood.

We use either a matching filler or some of the fine sanding dust — collected when sanding the floor — mixed with a hardening agent to ensure a close colour match.

It is left to dry and then buffed prior to the polyurethane being applied. Flood fill gives the floor a more uniform appearance. However, please be aware that it may crack and work its way out over time, particularly if the floor is installed on joists or battens. We use a German hardwax oil which comes in either clear or with a lightening base or a Belgian oil which comes in clear and a wide range of colours.

We use either a German or Swedish waterborne polyurethane. Polyurethane comes in a number of different sheen levels; matt for a natural timber look , Satin the one we would recommend and our most popular, possibly because it is the easiest to keep looking good!

Examples of these and oil can be seen in our showroom. The floor will be lightly sanded and then one or two coats of Sanding Machine For Wood Stairs Zip polyurethane applied. It is cheaper to recoat your floor at an early stage of wear than it is to restore a very worn floor.

If the polyurethane has worn through to bare timber, your floor will need to be completely sanded back and have new polyurethane applied.

If you are selling your property, polyurethane recoating will give your floor a much needed lift. See Recoating, Renovations and Repairs for further information.

Wood is a natural product which expands and contracts in reaction to the amount of moisture in its environment. A certain amount of movement is to be expected. We will leave an expansion gap around the edge of your floor to Sanding Machine For Wood Stairs To accommodate this. This gap is covered by skirting boards, toespaces, trims or gap sealant.

Trim is a finishing bar designed to provide a finished border for timber flooring. Trims are generally used between one flooring type and another, for example between wood and carpet or tiles. Trims and gap sealant are generally installed by the builder sometime after we leave. This guide will run you through:. Keep in mind:. On the CAMI scale, sandpaper grit is measured in microns, and to get an idea of how small a micron is, check out a piece of grit sandpaper.

The small grains on the sandpaper measure approximately microns in size, which is equivalent to. Very small. To make choosing sandpaper easier, manufacturers identify a coarseness level in words on the package in addition to the specific grade.

This is essentially a range of grit sizes that are similarly effective for the same sanding work. Not only does the density of sandpaper grit make a difference in the success of your sanding project, but the type of abrasive material does, too. Some types of grit grain are better suited to smooth and sand types of materials wood versus metal, for example. Sandpaper is very versatile by itself: You can fold a sheet into a palm-sized square, sand until the grit dulls, and then refold it for a fresh sanding surface.

If you have a lot to sand, however, you may be better off making use of Sanding Machine For Wood Manufacturer Difference one or more popular sanding tools.

Stanley Sweetheart Block Plane Spares List Rockler Murphy Beds 500