Rockler Circle Cutting Jig - Rockler Woodworking Tools

Using a circle cutting jig makes round table tops so easy. Then you add in the round option. Now, it gets even more tricky because you have to figure out how to cut a perfect circle or figure out how big to make it.

First, Rockler circle jig 2019 will literally list all the tools I used below. The router used in the video is discontinued. Before cutting the table top out, I obviously cut and Rockler Circle Cutting Jig Zoopla glued together a panel. I will cover making an entire table circlw a later video. To find the center of the panel, I measured from each of the four sides and made my marks. This rockler circle jig 2019 me a pretty good indication where the center would be.

When you have an odd sized panel you can measure from both directions, for example from the left and from the right. This will give you two marks close together that you can then split the difference, which is the center. The circle cutting jig comes with several pieces of hardware to attach many different routers.

For the record, I have an older Skil brand router, which rockler circle jig 2019 why I had to drill my own holes to attach my router.

The jig itself is made of a phenolic material so when I drilled my own holes they looked the same as the pre-drilled factory holes. The jig also comes with two centering pivot pins, which are used as a pivot point to route circles or arches. The jig is tightened down with a star knob to hold the pivot pin in place. First I drilled the holes for my router. I did this by removing rockler circle jig 2019 clear plastic rockler circle jig 2019 from my router and transferring those hole locations onto the circle cutting jig.

I drilled the holes using a tapered drill bit with an adjustable counter sink collar. The tapered drill bit allowed me to drill the exact size hole for the screws that are used with my router by rockler circle jig 2019 the counter sink collar to that location. Rrockler this point I attached the router to the jig using the screws for my router and the holes I just drilled.

One thing to mention here is that I left the clear plastic plate off when I attached the router to the jig. This is so that the screws would reach through the jig and screw into my router. The clear plastic piece would have made it too thick for the screws to work.

Now that I have attached the router to the roxkler cutting jigmy next step was to add the pivot pin. This consisted 20199 a t-bolt, a washer, a star knob, and a pivot pin. The t-bolt slips into the recessed track from the bottom and the washer is added from the top onto the bolt followed by the star knob.

I just knew I wanted to get the most out of the panel I glued up. So, from earlier, I found my mark in the center of the panel and placed the pivoting center pin there in a pre-drilled hole.

With the pivot pin installed and inserted into the center of the material I loosened the star knob and slid the circle cutting jig to the desired location. This way if the star knob rocklsr loose I could tighten it back up circcle the same place. The phenolic material this circle cutting jig is made of makes it easy to erase rockler circle jig 2019 pencil marks.

Actually cutting the circle was easy. Making sure the router and pivoting pin are secure is key to this operation. The first thing is feed direction. If you cut in a rockelr direction, this is known as a climb cut. When using the router in a router table, for example, you want to feed the material from right to left clockwise. In the video you can see me using the router with the jig in a clockwise motion.

I felt comfortable with ckrcle cut. Another thing to note while making the cut is to take shallow passes. If you try to take off a lot of material at once you run the risk of burning the wood or even breaking your bit. Have you ever had a rockler circle jig 2019 bit break in the middle of an operation? Not fun. The last thing I want to say is that you might not have a bit long enough to complete the entire cut, for example cutting through an entire 1.

The bearing allows the router to ride against the cut you previously made and the cutter will trim anything left behind leaving a flush edge. This bit has an end guide bearing, xircle I had to flip the table top to reference the previous cut. I will probably make another table in the future and I rockler circle jig 2019 definitely use this jig. I rockler circle jig 2019 see where this jig could be useful in other applications like arches.

Leave me a comment below if you have any questions about this jig or about the video. Thanks for stopping by. Outfeed Assembly Table.

Modular Shop Storage System. DIY Platform Bed. Stone and Sons content provides how-to videos on YouTube, step-by-step instructional website articles, insightful podcast episodes centered around community and other means of education through online courses and email communications. Subscribe and listen for tips, advice, rockler circle jig 2019, and stories from Shawn and other makers from around the world.

Topics range from project ideas, mistakes made, things we learn from, my kids point of view and anything related to woodworking, online content creation or community involvement.

Also, please share this post with your friends and family. Rockler circle jig 2019 you enjoyed this article, please consider sharing it with your friends and family by clicking any of the social media icons below.

It would be greatly appreciated. Rockler circle jig 2019 your information and click the blue subscribe button to receive future blog posts by rockler circle jig 2019. I cut the under side of the table top with the jig first then flipped it.

Save my name, email, and website in this browser for rockper next time I comment. This site uses Akismet to reduce spam. Learn how your comment data is processed. Sign in. Log into your account. Forgot your password? Terms of Use. Password recovery. Recover your password. Get help. Stone and Sons Workshop. Shop Projects. Share This Project! Receive our Blog posts! Cirlce you for signing up. There was an error submitting your subscription.

Please try again. First Name. Email Address. We use this field to detect spam bots. If you fill this in, you will be marked as a spammer. Patio Pergola. Live Edge Patio Bar. LED Shop Lights. Please enter your comment! Please enter your name here. You have entered an incorrect email address! Follow us on Instagram stoneandsonsworkshop. Box Columbus, MS

Your best source for high quality & innovative woodworking tools, finishing supplies, hardware, lumber & know-how. Find everything you need to make your next project a success. Family-owned since or support@www.- 8 Distributed by Rockler Companies, Inc. Medina, Mn Rev 01/18 Fig. 6 1. Mark a center point on your workpiece and lay out the perpendicular axes. 2. Center the Jig Base (2) on the intersection of the axes and secure it to the workpiece with screws. 3. Remove one of the Locking Pivots from the Jig Arm (1) and. Adjust the Jig Arm (1) in or out until the bit is positioned as desired to make the cut. Tighten the Locking Pivot. 7. With the router off,, rotate the Jig Arm (1) through the full range of cut. You want to ensure that the Jig Arm will move smoothly, as well as verify the circle pattern and proper placement of any spacers/supports. Then make.

Earlex Hvlp Sprayer Jp How To Build A Toy Guitar 2020 Kreg Table Saw For Sale France