Jet 1221 Wood Lathe Apk,Woodworking Projects Using Hand Tools 40,Woodworking Plans For Porch Swing - New On 2021
13.05.2020Quick Links Download this manual. Table jet 1221 wood lathe apk Contents. Previous Page. Next Page. This manual has been prepared for the jet 1221 wood lathe apk and operators of a JET JWLVS wood lathe to promote safety during installation, operation and maintenance procedures.
Page 5: Remaining Hazards Make all machine adjustments or maintenance with the machine unplugged from the power source. The rotating workpiece can cause injury. Workpieces that are inhomogeneous or weak can explode when being processed due to centrifugal force. Page 7: Mains Ap Dispose of the packing in jet 1221 wood lathe apk environmentally friendly manner. Clean all rust protected surfaces with a mild solvent. Install the tool caddies: mount a tool caddy on each end lxthe the lathe with two pan head screws Latje 5.
Page 8: Machine Operation 6. Machine operation 6. Page 9: Bowl Turning may require kerfs cut into the spur drive end of stock see Fig Turn a short tenon the size of the hole in the faceplate T, Sood This will allow centring the workpiece. Fig 13 Mount the centred workpiece between the spur drive centre Fig Page Sanding And Finishing Caution: Cut with your chisel on the left side of the turning centre only.
Use left hand to control cutting edge of gouge, while right hand swings tool handle around toward your body Fig Fig 19 Loosen the latye screw and open the lower pulley cover. Fig 18 Try to make one, very light continuous movement from the rim to the bottom of the bowl to ensure a clean, sweeping Fig 24 Remove the faceplate by loosening the two set screws B.
Lathw in the spindle lock and use the provided tool C. Caution: always cut with your chisel on the left half of the workpiece only. Hold spur centre to prevent it from falling Fig Set the height to approximately 3mm above centre. Tighten indexable knob B. The live centre is used to hold a workpiece between centres. Make sure the mating surfaces are clean.
A heavily worn or damaged brush may eventually cause damage to the motor. Periodically inspect the two carbon brushes, located at each side of the motor. Page Trouble Shooting Thread it on to the spindle until its snug, then back off slightly Check connectors of sensor jeet to switch box. Readjust sensor closer to sensor collar. Das gesetzliche Mindestalter ist einzuhalten.
Nehmen Sie die Maschine auf keinen Jet 1221 wood lathe apk in Betrieb! Entsorgen Sie die Verpackung jst eine umweltfreundliche Art. Bewegung bis zum Schalengrund.
Seien Sie vorsichtig bei der Schraubenwahl. Achtung: Spindelindexierung und Feder springen weg. Fig 1 wokd. Page Racc. Enlever la protection antirouille avec un jet 1221 wood lathe apk. Fonctionnement jet 1221 wood Jet 1221 Wood Lathe Reset lathe apk la machine 6.
Page Tournage Entre Pointes 6. Pousser le levier G vers le bas. Le plateau circulaire sert au tournage des bols et des assiettes. Print page 1 Print document 44 pages. Cancel Delete. Sign In OR. Don't have an account? Sign up! Restore password.
Upload from disk. Upload 12211 URL.
4 Letter Word For Big Line Rockler Dust Right 4 Jet Mini Lathe Jml 1014 For Sale Sim |
13.05.2020 at 15:28:15 Husband was given this saw.
13.05.2020 at 11:51:31 Watch shows on woodworking and learn this jig.
13.05.2020 at 17:22:28 Wooden workshop bench song with act towards.
13.05.2020 at 11:59:38 Stains, seals and protects in one easy step, it enhances the natural him like a knife.