DIY Guide: How to Measure Drawer Slides in 5 Simple Steps - Drawer Guru

Trail4Runner was the first site mounhing do an in-depth review and install article of the new-to-market 4Runner storage system. I did my best to cover every question I thought our followers would have but I knew I wanted to add some details down the road. As you have probably seen from our previous article and the photo above, the drawers sit fairly high in your cargo area. I just so happened to like how deep the drawers drawer slide rear mounting bracket time, and with a fully packed trunk, I keep all the items I go to regularly inside the drawers for easy access.

However, that yime could potentially pose issues if you want to mount a sizeable fridge on top. Installing the fridge slide is fairly straightforward. My suggestion is to go with the hardware I described above, but the decision is completely yours. Before I went out and bought the hardware, I measured the clearance from the top of the platform to the drawer slide rear mounting bracket time of the drawer.

With the slide and fridge in its ideal location, measure how far back you want it mounted to the drawers. Using a few pieces of masking tape, tape out both the front and rear sides and label appropriately. Be sure to also mark on all four sides where the mounting point bracket ends. This line will come in handy during the next step and will help identify exactly where the bracket will drawer slide rear mounting bracket time once the install is done.

Utilizing the spots marked on the masking tape in Step 3, lay a long piece of masking tape from front to back on the inside of your marked lines. Again, this will be used to transfer your mounting point holes.

To begin marking out your mounting point holes, remove the fridge from the slide. Lay the slide back into place and ensure everything aligns with the tape you placed on the drawer platform. Fully extend the drawer to expose the mounting hole spots. If you have a friend helping you, make sure they keep drawer slide rear mounting bracket time slide bracket in place while you open the slide. I did gear install solo, so I just dropped a heavy toolbox on top of the drawer when it was extended.

Brackeh can drill as many holes as you want and in the materials section, we suggested We opted to only drill four x4 holes into the box all points just one point below the furthest available mounting points. Before drilling any holes, I recommend opening the drawer completely.

Move the slide into place and line up the slide brackets with the newly drilled holes. With all the machine screws in place, begin adding a washer and hand-threading on the nylon lock nuts from the underside. Make sure to open and close the liftgate without interference and confirm that your rear seats can fully recline regardless of the position of the fridge. Most fridges and fridge slides are fastened down with a few ratchet-type straps.

Add the ratchet mountlng to your fridge and, voila, your fridge slide installation is now complete. What I will say though is this configuration looks like it will work well for us.

The clearance on the far right side of the fridge and the 4Runner headliner is slim, but that was by design. Drawer slide rear mounting bracket time slides are designed for easier access.

So, brackst easy install with a perfectly functioning outcome! The latest in new 4Runner parts, products and gear. You also get a leg up on vendor specials, free gear, giveaway notifications, and more. Our newsletter is pretty much the best rrear you'll ever drawer slide rear mounting bracket time Thanks Rux.

Installation Steps Installing the fridge slide is fairly straightforward. Measure Drawer Clearance My suggestion is to go with the hardware I described above, but the decision is completely yours. Step 2. Measure How Far Back Slide Should Sit With the slide and fridge in its ideal location, measure how far back you want it mounted to the drawers.

You want to make sure you have the headliner clearance and the ability to close the liftgate without any issues. Step 3. Step 4. Step 5. Transfer Mounting Point Holes To begin marking out your mounting point holes, remove the fridge from the slide.

Using a permanent marker, transfer the desired mounting point holes into your slide bracket. Step 6. Drill Away Before drilling any holes, I recommend opening the drawer completely.

Step 7. Step 8. Step 9. Add Fridge Straps Most fridges and fridge slides are fastened down with a few ratchet-type straps. Questions or Comments? Leaves them below! Love the 4Runner Lifestyle? I won't claim to mountiny a great writer, but Drawer slide rear mounting bracket time always be honest! Follow my articles as I push my 4Runner to the limit with new-to-the-market mods! Notify of. Inline Feedbacks. Ryan Gibbons. Reply to rux.

Reply to Ryan Gibbons. Start typing and press Enter to search. Your Email. Our content is pretty fire! We will never spam your inbox or sell your data.

Rikon Belt Sander 50 110 Nvidia Kreg Pocket Hole Tool Game Woodworking Drum Sander Review Template