How to select the right cabinet hinge for your home Blog Categories: Select a category We use cookies to make wikiHow great. Deals and Shenanigans. Eligible for Free Shipping. Overlay Cabinet Doors can be matched to specific hinges of various dimensions. All rights reserved. There are 17 references cited in this article, hinbes can cupboard door hinges installation quarterly found at the bottom of the page.

Measure and mark 3. Use a ruler, tape measure, or combination square to measure the distance from the top edge of the cabinet door and mark a horizontal line with a pencil. Then, measure from the bottom edge of the door and mark a line. Place the hinge on the door and mark the distance from the edge. Use a pencil to mark around the hinge so you know where you need to bore your hole.

Repeat the process for the mark you made at the top of the cabinet door. A Forstner drill bit is used to bore holes into wood to install hinges. Then, adjust the line depth on the side of the bit so you can know when to stop boring into the wood. Place the bit on the center of your marking and bore to the depth line. Hold the end of the bit against the cabinet door in the center of the line that you marked. Bring the drill up to speed to start boring through the wood.

When the bit reaches the line depth that you set, stop boring and remove the bit. Repeat the process for the other hinge location marked on the door. Apply pressure against the drill to drive the bit into the door. Insert the hinge cups and drill wood screws into the screw holes. The hinge cup refers to the convex, cup-like part of the concealed hinge that goes inside of the bored hole in the door.

Fit the cup of the hinge into the hole so the screwholes are flush against the surface of the cabinet door. Shim the door in place and measure the gap. Shim the door against the cabinet and use a ruler or tape measure to measure the small gap between the cabinet door and the cabinet surface. Mark 2. Measure the distance from the edge at the front of the cabinet itself. Mark a line with a pencil that runs from the top of the cabinet down to the bottom so you can intersect it with your hinge measurements.

Add the gap to the height and mark the top and bottom of the cabinet. Take your gap measurement and add it to 3.

Then, measure that distance from the top and bottom of the cabinet and mark the locations with a pencil. When you make your marking, the 2 lines on your cabinet should intersect. Align the mounting plate where the lines cross and drill them into place. Place the mounting plate at the location where both lines intersect and line it up so the screw holes are even.

Use a power drill to drive screws into the screw holes to secure the plate in place. Then, attach the other mounting plate to the cabinet in the same way. Hook the hinges onto the mounting plates and snap them into place. Press on the bars of the hinge to snap them into place on the mounting plates.

Open and close the door to make sure the hinges work and the door is even. Method 2 of Choose a traditional hinge to add a stylistic detail to your cabinets. Traditional hinges are mounted to the surface of the cabinet door and are visible, or partially visible when the door is closed. There are a variety of traditional hinges including, butt hinges, flush hinges, and antique hinges, but they all fit onto your cabinets in a similar fashion.

Look for traditional hinges at home improvement stores, hardware stores, and online. You could also look for ornate or decorative hinges at antique stores. Start by placing the hinges on the cabinet where you plan to install them, wrapped around the outer edge of the cabinet wall in the open position.

The hinges should sit flush against the outside and inside of the cabinet. The spacing needs to be even so the cabinet door fits correctly and opens and closes smoothly. Write down the measurements so you can duplicate them if you plan to install hinges on multiple cabinets and cabinet doors. Drive screws into the screw holes on the cabinet.

Once the hinges are aligned, screw the cabinet-side of the hinge to the cabinet with a power drill. Add a line of hot glue to the top of the hinges and place the door on top.

Apply a line of hot glue to the top of the hinges and place the cabinet door on top of them. Open the door and drive screws into the screw holes on the door. Use a power drill to drive screws into the screw holes to secure the hinges to the door. Include your email address to get a message when this question is answered.

By using this service, some information may be shared with YouTube. Submit a Tip All tip submissions are carefully reviewed before being published. Read on for your complete guide to selecting the right cabinet hinge for your project. Any questions? Call or email Hinge Outlet sales hingeoutlet. Face Frame Cabinet Hinges are partially concealed hinges. The part attached to the frame is visible, while the part attached to the door is hidden, unless the door is open.

Face Frame Cabinet Hinges are available in a variety of sizes, styles, and finishes, allowing you to completely customize your hinges to your cabinet thickness and design style.

Certain Face Frame Cabinet Hinges are self-closing. Soft Close Cabinet Hinges - Soft Close Cabinet Hinges are a type of surface mount cabinet hinge that closes gently, no matter how much force is exerted to close the cabinet door. Soft Close Cabinet Hinges are popular with families, reducing noise and the risk of injury, while protecting your investment.

Soft Close Cabinet Hinges are precision adjustable, therefore we recommend you hire a professional installer for the best performance outcome. Self-Closing Cabinet Hinges - Self-Closing Cabinet Hinges are just that — cabinet hinges that enable you to close the door without having to guide it to a complete close… a complete lifesaver in the kitchen! So how do they work? Self-Closing Cabinet Hinges have springs built in, giving them just enough added closing power to help finish the closing action.

To activate the self-closing action on a Self-Closing Cabinet Hinge, give it a gentle nudge. Once the door reaches a certain point in the closing process, the spring activates and pulls the door closed the rest of the way, so that it is securely shut against the cabinet. With periodic oil and maintenance, our Self-Closing Cabinet Hinges will last the lifetime of your cabinets. Demountable Cabinet Hinges: Single and Double. Demountable Cabinet Hinges allow you to remove the cabinet door.

Single Demountable Cabinet Hinges are installed on the face of the cabinet frame with screws, and the hinge fits into a slot on the edge of the door.

Double Demountable Cabinet Hinges have two slots - one in the face of the cabinet frame and one on the edge of the door. Non-Mortise Cabinet Hinges are used on Inset Cabinet Doors and are an excellent choice for adding decorative detail to your cabinets.

The downside is, with no mortises, if the screws are protruding at all, the Non-Mortise Cabinet Hinge won't close properly, so we recommend you hire a professional installer for this type of hinge. For the purpose of selecting cabinet hinges, Cabinet Doors are identified by the style of installation used in the cabinet construction process:.

Overlay Cabinet doors do exactly what the name implies: They cover the cabinet opening completely, overlapping the cabinet case or face frame on all sides. Overlay Cabinet Doors can be matched to specific hinges of various dimensions. Full Inset Cabinet Doors fit entirely within the cabinet opening and sit flush with the cabinet sides or face frames when in the closed position.

Offset Cabinet Doors are common in older homes, and are compatible with H, L, and strap hinges, as well as surface mount hinges. Now that you know about hinge and cabinet door types, we have a few helpful hints for proper cabinet door hinge installation:.

Hinges are made from a variety of metals including stainless steel, brass, steel, and bronze. Finishes include primed, polished and plated, and rust-resistant depending on your project needs.

Makita Xmt03z 18v Lxt Lithium Ion Cordless Multi Tool Gpu Ryobi Router Bits Tongue And Groove Model Types Of Wood For Turning Quest