Euro/Epoxy Drawer Slides - The Hardware Hut

In one of my recent tutorials, I built this miter saw station out of 2x4s. As usual I had it cut down into manageable sizes at the store, and then made the final cuts in the shop. So after ripping all my pieces to width, I moved over to my miter saw to cut them to length. Now my miter station is 24 inches deep so I bought some 24 inch drawer slides.

BUT, before going any further, let me point something out. Euro slides are metric. For once! So since my slide a are 60 cm, I set my stop block to 60 cm and cut all the sides for my 4 drawer boxes without moving the stop block. With all of the sides cut to length, I could move on the the front and back pieces. I started by measuring the width of the opening and used this method to figure out the exact length I would need to cut.

Basically you 23 inch euro drawer slides co the width of your opening I set my stop block to Then to account for twice the width of the plywood, I simply used 2 offcuts that I placed up against my stop block.

Because plywood thickness can vary, I find this method easier than doing the math and less prone to making errors. Oof okay, the hard part is out of the way and I can now move onto to making pocket holes to prep for assembly. To assemble the drawer boxes I used some wood glue and 1 inch pocket screws.

It helps to use a clamp to hold the boards in alignment during assembly, at least for the first screws. I repeated the very same process and the other side of the box, and was then ready to move onto the drawer bottom.

I measured and cut a bottom panel to size, again using half inch plywood. I then secured the drawer bottom using glue and brad nails.

After wiping off the excess glue, it was time to move onto the drawer slides. Installation on the drawer boxes is pretty simple. You just place the slide on the bottom edge of the drawer and attach it with the provided screws.

For the back end, I used a magnetic level to make sure the slide was level and marked out the pilot hole. I made the pilot holes and then loosely attached the front screw and 23 inch euro drawer slides co back one, then checked for level again before fully tightening the screws.

I repeated the same process on the other side and was then finally ready to install the drawer. And I was happy to see that everything fit just as planned. After a quick measure, I trimmed down the side pieces I had previously cut and assembled the box just as before.

When installing the slides, just remember that the part with the wheel needs to stick out since this will be the back side of the drawer. After installing the slides, I could do a test fit to make sure everything fit nicely. Alright, with all my drawer boxes made I can move onto to making the drawer fronts. I started with the bottom drawer and measured the height so it would sit just below the drawer above without interfering.

Once I was happy with it, I drilled some shallow pilot 23 inch euro drawer slides co making sure not to go all the way through and secured the drawer front with some screws from inside. Then I essentially repeated the same process working my way up through the 24 Inch Euro Drawer Slides Zoom drawers using washers as spacers between the drawer fronts.

It helps to pull out the drawer slightly so you can hold it in position and check the alignment with the bottom drawer. Again, once I was confident, I used spring clamps to hold the front in place then secured it with some screws after making pilot holes. To install the knobs, I first marked a center line and used this cabinet hardware jig to make the screw holes. Then I just screwed the knob into place.

I love having this extra storage in the shop for all the stuff I never know where to put. What would you put in 23 inch euro drawer slides co Basic Shop Drawers. Get New Projects in Your Inbox! First Name. Related posts:. Keyhole Router Bit Jig.

Circular saw guide. 23 inch euro drawer slides co Saw Dust Collection. Trapezoid Leg Bench. Hexagon 23 inch euro drawer slides co Jig.

European drawer slides are an economical roller-style slide that feature easy installation. Available in 3/4 and full extension for maximum drawer accessibility. Euro/Epoxy Drawer Slides 26 Items Total. Sort By $ GRA Grass 32" Premium European Drawer Slides - PAIR (White) $ GRA 2-Pack in Self-Closing Drawer Slide. Model #TUSC2G Compare; Find My Store. for pricing and availability. Richelieu. OVIS offers a large selection of drawer slides from Hettich, Fulterer, Sugasune and Hawthorne & Reid. We offer: epoxy coated euro slides, ball bearing drawer slides, full extension, over extension, undermount drawer slides, heavy duty to lb class drawer slides, keyboard slides .

Wood Carving Shops In Kandy 01 Drawer Under 100 Zero Best Steel For Wood Carving Knives Guide