Tongue and groove is a method of fitting similar objects together, edge to edge, used mainly with wood, in flooring, parquetry, panelling, and similar constructions. Tongue and groove joints allow two flat pieces to be joined strongly together to make a single flat surface. Before plywood became common, tongue and groove boards were also used for sheathing buildings and to construct concrete formwork. Tongue and Groove / Rail and Stile Router Bits - Shaker Style Doors Making.  Shaker Door Made Using A Tongue & Grove Bit Set. Wes Hamstra. Tongue Groove Set Router Bits Wood Tongue And Groove Router Set Windows Door Flooring 3T Adjustable 8mm Shank Durable. Brand Tongue And Groove Router Setup Quest new. EUR From China. Buy it now. + EUR postage. 24 sold.  0JSpXonsoHKredSDFXZ9. Tongue and Groove Router Bit Set 8mm Shank 3 Tooth Mortise Cutter 2 Bits. Brand new. EUR From China. Buy it now. Free international postage. 12 watchers. Whether you are searching for the best tongue and groove router bit for flooring or some other purpose. If the cutting edge tongue and groove router set notification into the groove with the board inverted, the bit height is correct and the groove is centered. Amazon reviewers gave the Rockler Tongue and Groove Router bit a 5 out of 5 average score. Adjust and lock the fence so the bit is centered between its reference marks with the workpiece abd in place. Again move the fence forward and match the position of the fence according to the bit with the scale and fix the fence. It looks very nice. On Amazon, the Yonico has anv average review score of 4.

Install the slot cutter, and adjust the bit height to meet the layout marks see Photo 6. Step 2: If the fence facings are adjustable, close up the fence around the bit to eliminate gaps around the cutters.

Make the first set of passes, flipping the workpiece over between cuts to center the groove. Re-tighten Tongue And Groove Router Setup Kit the fence. Follow the same cutting process as you would with a rabbeting bit to form the tongue, raising the bit with each set of passes until you shave away all of the waste see Photo 8 and steps 4 and 5 of the second technique.

Hold a ruler over the bit and rotate the cutter by hand to check your fence setting carefully see Photo 9.

Close up the fence facings around the bit, if possible. Step 3: Lower the bit as you would when using a rabbeting bit or slot-cutter, and follow that same cutting process, raising the cutting height a little at a time until the tongue is just a bit thicker than its groove see Photo Use the grooved workpiece to adjust the bit for the last passes that bring the tongue to final size see Photo 4.

Questions and Answers. Product Reviews. Related Products Check items to add to the cart or select all. Router Bit Vise. Cabinet Door Router Bit Sets. Slot Cutter Master Set. Login Register Registered Customers. If you Tongue And Groove Router Setup 45 have an account, sign in with your email address. Sign In. Forgot Your Password? Personal Information First Name. Last Name. First, install the tongue cutter bit in the router table with both cutters installed and the nut snugged down.

Lay the groove gauge block made earlier on the router table next to the bit and adjust the bit height so the top edge of the lower tongue cutter is flush with the bottom edge of the groove. If the top cutter is not even with the upper edge of the groove, note the amount of error and install enough spacer washers below the cutter to raise it that amount. With the nut secured on top of the tongue cutter, align it to the groove gauge block again to check the alignment.

When satisfied with the alignment visually, cut a tongue in a piece of scrap the same thickness as the project wood. Test the fit of that tongue into the groove gauge block and make adjustments to the spacing washer configuration as needed. If the tongue fits the groove properly but the faces are out of alignment, adjust bit height to compensate. When satisfied with the fit and alignment of the faces, make a cut in a fresh piece of scrap and save it as a gauge block to be used in the future for setting up the tongue cutter bit.

After using the tongue and groove bit set a few times the setup goes very quickly. Another benefit of this procedure is when making additional tongue and groove stock of the same thickness, this setup will produce new pieces that fit existing stock correctly.

Take your time, use scrap wood that is the same thickness as the wood to be used in your projects and all will go fine! Do you have a comment about this page?

Back to the Tips, Tricks List. Follow NewWoodworker. This is a Veteran Owned site. This setup procedure is simple and easily repeatable. Click image to enlarge. Setting the fence flush with the bearings insures correct dimension of the tongue and groove.

Softwood Lumber Products Meaning 60 Woodworking Turning Table 4d Brick Moulding Router Bit 500