Hey, guys! The great thing simple small wooden Simple Small Wooden Box Plans 50 box plans 10 boxes is that you can make them many different ways and for a ton of different purposes. The drum sander is going to allow me to make custom sized stock without tearout in heavily figured wood. Seuss books. This is a great way to try out box making and you can add hinges, locks, drawers, trays, etc.

Before we get started, make sure to follow me on InstagramFacebookYouTube and Pinterest to keep up with all my latest builds and free projects! Affiliate links are used on this page.

See my disclosure page for info on affiliate programs. I like the ratio look on the box and this size seems to be just big enough to be substantial, but not too big. I also have jewelry box plans for beginners above so make sure to check those out. The best part is this build takes very little wood. So you can buy nice hardwoods for the box and not break the bank.

So I cut material for two boxes which you will see some parts for both boxes in the pictures. I used simple small wooden box plans 10 maple for the sides of the Simple Small Wooden Box Plans List box and walnut for the top, bottom, and lining for a nice contrast.

I used a larger piece of walnut with some nice figure to make my tops and bottom panels. I simple small wooden box plans 10 the walnut into 2 pieces on the bandsaw then cut those in half to finish with 4 pieces. This is one of the best uses for the drum sander in my book.

After they were flat I glued the pieces together into 2 panels and then cut them to size. Next, cut the grooves in the sides of the DIY jewelry box for the top and bottom panels. Do some test cuts in scrap before making the grooves to be sure your top and bottom panels fit snugly.

By cutting the sides from the same piece you can achieve a continuous grain flow around the whole box. Assemble the jewelry box by laying the side pieces end to end in a straight line and taping the joints on the outside.

Clamping the glue up with a web clamp makes this much easier, but f-clamps work well also. After the box is dry sand the sides to grit before simple small wooden box plans 10 next step. Yes, I realize this a wooden box with no way to get inside…patience my friend. I got burning on the top edge of the jewelry box, so I took it to the drum sander to remove the burn marks and get everything level.

I also did this to the underside of the top. Feeding the box in on an angle helps reduce your chances of snipe. You can also flatten the parts on a sheet of sandpaper stuck to your tablesaw.

The last piece of the jewelry box simple small wooden box plans 10 the lining which serves as decoration as well a lip for the lid. Simple small wooden box plans 10 can miter these corners as well, but stacking miters inside miters is a bit more tricky.

Glue the pieces in place and clamp with some spring clamps. Put the short pieces in first and sand everything to grit before installing. After the glue has dried, touch up any sharp edges and do a once over of the whole jewelry box with grit sandpaper. Now apply your finish of choice. I used simple small wooden box plans 10 to really pop the grain of the maple but not yellow it. I applied 4 coats and finished it with a beeswax mixture. Even though I used some fancy wood, this simple DIY wooden jewelry box build is easy Simple Small Wooden Box Plans Us to make and a great way to get started in box making.

You can do so many more things with boxes, like splines, hinges, trays, etc. Very nice project! I like the combination of maple and walnut. I would imagine those cuts need to be fairly precise. Thanks for the inspiration.

Yup, I used the miter gauge with a wood backer and a stop block. If you watch the video you can see it in use. And thanks! No splines to support the miter corners? Probably going to follow your design and see how it goes! I mitered the ends of my inserts Simple Small Wooden Box Plans 40 and cut them so the fit really tight. I also chamfered the top lips of the lining to about 45 degrees so that I could hinge the lid.

And, simple small wooden box plans 10 book-matched panels are sweet. I tried making a second box with store-bought oak boards I still have no planers… and my mitered corners came out all screwed up… I can only guess that when I cut them to 45 degrees on my table saw that the hardness of the oak is deflecting the blade and making my cuts really wonky. I was trying to make a box for a foam insert to go into so I needed the sides to be really precise in length and chopping at them over and over with the table saw really ruined that.

But just doing one set is doable if you really take your time on setup and fitting. Glad you are getting after it! Nice job of making this nice tutorial… Wish I had your equipment…. Easily followed and you made a stunning box that anyone would be proud of….

My awesome husband made 6 of them for Christmas presents for our adult kids this year…. Log in to leave a comment. Fix This Build That. Assemble the Simple Wooden Jewelry Box Assemble the jewelry box by laying the side pieces end to end in a straight line and taping the joints on the outside. Install the Lining on the DIY Jewelry Box The last piece of the jewelry box is the lining which serves as decoration as well a lip for the lid.

Apply A Finish to the Wooden Jewelry Box After the glue has dried, touch up any sharp edges and do a once over of the whole jewelry box with grit sandpaper. Is there an alternative way to cut the lid for the box without a table or band saw?