Lathe-Mounted Disc Sander: Sanding machines are fairly common in most woodworking shops, with models ranging from small tabletop versions to high-powered floor models. When still living at home, I used a combination belt/disc sander in my minuscule shop to shape and correct n   I had originally built a 12” version to fit the discs I had on hand and used a wood box for the tabletop. It wasn’t very accurate and would occasionally get pushed into the disc. So, time for a better one. Sanding smooths the wood which prepares our project for painting or staining. Wood that isn’t properly sanded could mean that we see scratches or imperfections on the surface of our finished project. Originally published June 7, updated November 13,   We smooth out wood by sanding. We start with a more aggressive sandpaper grit and move progressively to less aggressive sandpaper grits. My approach for sanding DIY projects is to start with the least aggressive grit necessary to smooth the wood.  It’s almost like I forgot to attach a sanding disc. Out of curiosity, I flipped the sander over and “Hey, where’s the sanding disc?!” I found the disc on the floor, stuck it back on and turned on the sander. Описание: Деревянная чаша Sander Sanding Инструмент с шлифовальным диском для токарного станка. Спецификация: Материал: нитрид бора Применимо промышленности: столярные изделия Наждачная бумага: 6шт Капот полировщика: 1 шт. Гаечный ключ: 1 шт. Особенности: Хороший инструмент для шлифования чаш. Sandlng operating speeds for disc sanding are determined by the grit you're using and the material you're sanding. Accept Cookies Customise Cookies. Compare Selected. A light, momentary pressure is all that's needed. Sanding Circles Circular workpieces sanding discs for wood lathe 6th be sanded freehand. I think I might install some fins that will boarder the outside of the disk to increase the suction just a little more.

These are usually used if you want to mount an extension bed to the lathe to they are threaded to receive bolts already!

There are 4 holes on the bed of the lathe, so I attach 4 matching bolts to hold the table in place. While it is mounted on the lathe I trace out the edge of the disk and the edge of the bed on the table.

I cut along this line on the bandsaw to bring it down to shape. Besides the support piece I just built and the actual table surface, I want to install support bracket as well. To attach the table top I decide to use pocket holes since it will keep me from having any fasteners on the top of the table top.

This is then all screwed into place. A couple of screws through the bracket and a few through the support piece for the table. I want to add some sort of dust collection to this because otherwise it will make a mess. I use a forstner bit to drill a large hole on the left side of the table the same size as the end of my vacuum hose.

To help collect the dust at this spot, I want to help funnel it, so I draw a line on either side to cut to with the router. I install a couple of small ramps to have the router cut deeper towards the hole. These little ramps guide the router up and down into the work piece while I work it back and forth to form the cavity.

After the router, I just clean it up a bit with the chisel. Then I install it in place again and it looks great! Even the dust collection works surprisingly well.

I think I might install some fins that will boarder the outside of the disk to increase the suction just a little more. I decided to get rid of 2 of the bolt holes because I figured out that just 2 of them was sufficient so I made them into slots instead. I also cut out some star knobs and epoxied them to the heads of the bolts so I don't need to look for a wrench every time I want to install it.

Thanks for checking out the build and be sure to check out the build video too for the full experience. Hi I really enjoyed watching the building of your sander. I am just a starting woodworker. The only comment I have to make is that most of the projects are being build with thousands of dollars of woodworking machines what makes it difficult for guys just starting with just handtools to work with.

Before you build a 16" disc sander, you might want to check the difference between the price of 12" vs 16" disks. Also if you have a way to do it put a very slight convex shape on the sanding disk. And tilt the axis of the disk by the same amount.

Much easier to get a flat sanded surface. Believe it or not. Only the part of the sanding disk that is at a right angle to the base plate will be sanding.

But since it's turning the whole disc is used. There will also be far less tendency for the piece being sanded to catch and jerk out of you hand. Heavy duty disc sander I congratulate you on this neat work. The motor on my Shopsmith 5 lathe can barely take a slight load after running it on a 50 cycle power.

It's too hard to find a strong motor to fit inside the carriage. Well, that's my problem, someday I'll win. Nicely done! I built a similar ible a few years back but didnt think about securing the table to the end of the bed.

More by the author:. About: I have an unhealthy relationship with pallet wood. I make fast paced and entertaining build videos on my YouTube channel that are made for everyone, but with the ultimate goal to get the younger generations ex… More About JackmanWorks ». I start by cutting out the pieces for the disks on my table saw, just over 16" square.

Thanks for making a great product available. This industry may be another good bunch of craftsmen to provide your products too. Unless Hawaii is calling your name…. And the bonus is that my go-to finish is Danish Oil, so sanding with oil is just like starting the finishing early. It knocked down that nasty end grain like spreading butter on toast. I owe ya. Do you use this sanding method often?

Or just in problem areas? I am now adding you to my official Christmas card list, and if I ever actually DO send out Christmas cards, you will most assuredly get one e-card of course. As it turns out I know everything else in the world there is to know except for sanding with oil , but its always possible that I missed something. Superior Sanding Products and Service. The Original WoodNWonders. Turning Tools and Accessories. Artists and their Tools.

Titebond Hide Glue Guitar Youtube Swiss Wood Carving Museum Limited Interlock Signmakers Templates Tutorial