Makita Table Saw | | www.-

Manufacturer reserves the right to change specifications without notice. Note: Specifications may differ from country to country. Read the owners manual carefully. Learn Dont force tool or attachment to do a job the tools poser and limitations, as for which it was not designed; for example, well as the specific potential hazards dont use mmakita saw for cutting tree limbs peculiar to makita 2703 miter gauge power. Wear no loose clothing, gloves, neckties, rings, bracelets, or other jewelry which makita 2703 miter gauge power. Wear protective Form habit of checking to see that keys hair covering to contain long hair.

Also use face or dust mask if cutting oper- makita 2703 miter gauge power. Everyday eyeglasses only Cluttered areas and benches invite acci- have impact resistant lenses, they are dents. NOT safety glasses. Use clamps or a vise to hold work when Dont use power makita 2703 miter gauge power in damp or wet loca- practical. Its safer than using your hand tions, or expose them to rain.

Keep work and it frees both hands makits operate tool. Dont use tool in pres- ence of flammable liquids or gases. Keep proper footing and balance at all 6. All visitors should be kept safe distance from work area. Keep tools sharp and clean for best and 7.

22703 instructions for with padlocks, master switches, or makita 2703 miter gauge power lubricating and changing accessories. Make sure switch is in off position before Dont leave tool until it comes to a com- plugging in. Consult the owners manual for recom- mended accessories. The use of improper This plug will fit in If the plug Serious injury could occur if the tool is does not fit fully in the outlet, reverse the tipped or if the cutting tool is accidentally plug.

If it still does not fit, contact a quali- contacted. Do not change the plug in any way. A binding of moving parts, breakage of power source with voltage greater than parts, mounting, and any other conditions that specified for gahge tool can result in that may affect its operation.

Using a power source with voltage less than the name- Feed work into a blade or cutter against the direction of rotation of the blade or cut- ter only.

Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Table 1 shows the correct size to use depending on cord length and nameplate ampere rating.

If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord. Table 1. If you use this tool unsafely or incorrectly, you can suffer serious personal injury.

Wear eye protection. NEVER wear gloves during operation. Dont use the tool in presence of flam- Keep hands out of the line of makita 2703 miter gauge power maklta mable liquids or gases. NEVER makita 2703 miter gauge power the tool with an abrasive NEVER stand or permit anyone else to cut-off wheel installed.

Check the blade carefully for cracks or damage before operation. Replace cracked Make sure the blade is not contacting or damaged blade immediately. Clean the spindle, flanges especially the installing surface and hex nut before Before cutting an actual workpiece, let installing the blade.

Poor installation may the tool run for a while. Use saw-blade powre and spreader for NEVER make any adjustments while every operation for which it can be used, tool is running. Disconnect tool before including all through sawing operations. Always assemble and install the blade guard makita 2703 miter gauge power the step by step instructions out- Use a push stick when required.

Push lined in this manual. Through sawing opera- sticks MUST be Makita 2703 Miter Gauge Valve used for ripping gajge tions are those in which the blade cuts workpieces to Makita 2703 Miter Gauge Location keep your hands and fingers mitfr through the workpiece as in well away from the blade. NEVER use the tool with a faulty blade guard or secure the Pay particular attention to fauge for blade guard yauge a rope, string, etc.

KICKBACK is a sud- irregular operation of the blade guard den reaction to a pinched, bound or misaligned should be corrected immediately. Immediately reattach the guard and operator.

Do not cut metals such as gaige and spreader, antikickback pawls and blade guard screws. Inspect for and remove all nails, in place and operating properly, by not releas- screws and other foreign matter from the ing the workpiece until you have pushed it all workpiece before operation. Remove wrenches, cut-off pieces, etc. Do not perform any operation freehand. Dont abuse cord. Never yank cord makita 2703 miter gauge power Freehand means using your Makita Table Saw 2703 Miter Gauge hands to sup- disconnect from receptacle.

Mzkita cord port or guide the workpiece, in lieu of a rip away from heat, oil, water and sharp fence or miter gauge. NEVER reach around or over saw Some material contains chemicals blade. NEVER reach for a workpiece until which may be toxic. Take caution to pre- the saw blade has completely stopped. Follow material supplier safety data.

Avoid abrupt, gaueg feeding. Poer as slowly as possible when cutting hard work- The guard can be lifted during work- pieces. Do not bend or makita 2703 miter gauge power workpiece while piece setup and for ease of cleaning. If you stall or jam the blade gauye the Always make sure that guard hood is workpiece, turn the tool off immediately. Then clear the jam. NEVER remove cut-off pieces near the blade or touch the blade guard while the blade is running.

Assemble as follows:. Installing saw blade Remove the table insert on the table. Hold the outer flange with the offset wrench and loosen the hex nut counterclockwise with the wrench. Then remove the outer flange. Assemble the inner flange, blade, outer flange and hex 3 1 2 nut onto the arbor, making sure that the teeth of the blade are pointing ma,ita at the makitaa of the table.

Always install the hex nut with its recessed side makita 2703 miter gauge power the outer flange. Outer flange matter; it could cause blade slippage. Be sure that the 2. Hex nut blade is installed so that the teeth are aligned in the cut- 3. Inner flange 4. Saw blade ting turning direction. To secure the blade in place, hold the outer flange with makuta offset wrench, then makita 2703 miter gauge power the hex nut clockwise with the wrench.

If your grip should slip, the wrench may come off the makita 2703 miter gauge power. Wrench hex nut, and your hand plwer strike the sharp blade 2. Offset Wrench edges. Insert the gage between the blade guard mounting portion stay and the pressure plate. Blade 2073 2. Spreader 3. Antikickback pawl 4. Pressure plate. Tighten mter hex bolts A with the offset wrench.

The 3 1 6 2 spreader installing location is factory-adjusted so that the blade and spreader will be in a straight line.

Buy a Makita Miter Gauge Assembly [] for your Makita Power Tool - Fits Makita model Departments Table Saw Table Saw. Table Saw Table Saw. Products Compatibility. This item works with the following types of products:Brand: Makita. Makita Miter Guage - Power Rotary Tools - www.- Skip to main www.- Makita Rip Fence, , out of 5 stars $ Fulton Precision Miter Gauge with a Standard Slot (3/4” x 3/8”) Steel Bar with Adjustable Spring Loaded Plungers and /5(7). Miter Gauge Assembly. $ Part Number: In Stock, 10 available Power Tool Care and Maintenance This article suggests guidelines for power tool care and maintenance. It also describes information tools available at www.- Makita schematic. Hope this helps, WJA Join our VIP Email list.

Best Wood For Indoor Projects Womens Primadonna Xs Etam 36365m