It's slightly more expensive, and slightly better quality, although it is questionable how much of a difference this makes Laguna 14 Bandsaw Manual Quest in practice. Previous Page. All lafuna surfaces will rust if not protected. Loosen the clamp screws that are located on the cast bracket. The tension scale does not register until the blade is relatively taut and is located laguna 14 bandsaw manual user the inside of the body of the bandsaw. Page 4

Equipped with a premium blade it delivers consistently high quality cuts. Online Dealers View Dealer Locator. The handle of this spatula is turned, and the end is shaped using the bandsaw and sanding. Make more than one, everyone you know will want a spatula. I like to build arts and crafts style furniture, and many pieces have a gentle curve that graces the lower stretcher. Read More Bandsaw Circle Cutting Jig Most woodworkers find the need to cut circles at some point, and there are multiple ways to accomplish the task.

Read More View More Blogs. Designed in United States. Production status New. User rating 1 vote. Ceramic Blade Laguna 14 Bandsaw Manual Report Guides. Machine overview. By Rob. Ceramic blade guides The blade guides can be set without any tools, and the fact that they are ceramic sets them apart from the competition. Ceramic Blade Guides Useful features The 14 12 also has most features you would expect on a premium bandsaw.

Upgraded version There is also an upgraded version of the 14 12, called the 14 BX , which has a foot pedal break, more powerful motor, and a frame made from a heavier type of steel. Machine Atlas Verdict. Value for money A. Quality A. What we don't like No foot pedal break Bottom ceramic guide can be tricky to adjust. What we like Excellent build quality Ceramic blade guides Reasonable price Windows for blade tracking and tension Powerful for a V machine. Add it here Machine Atlas Guides.

Review by Jory Brigham youtube. Review by Dave's Woodshop youtube. General Official Page on Laguna's website lagunatools. Page 19 Fence Steel block Fixing screw Fence in low position The bandsaw is supplied with an aluminum fence. Assemble the fence to the cast-iron bracket with the bolts and steel block provided. Adjustment and squaring of the fence will be covered later in the manual. Slide Laguna 14 Bandsaw Manual Test the Fence in high position bracket onto the round steel bar attached to the table.

Page 20 Bottom blade guards Bottom blade guard It is very important to have the blade covered for safety. Guards are provided at the top of the lower door and just above the table dust port. The door guard must be moved vertically and clamped in position before operating the bandsaw. Page 21 The switch is mounted on the main pillar of the bandsaw in the incorrect position for operation.

This is for transport reasons, and the switch will have to be moved to the operation position prior to starting the machine. Remove the two screws, reposition the switch box and reassemble the screws. Page Adjusting The Bandsaw Use a push stick at the end of a cut. This is the most dangerous time because the cut is complete and the blade is exposed.

Push sticks are commercially available. Hold the wood firmly and feed it into the blade at a moderate speed. Page 23 2. Inspect the teeth and the general condition of the blade. If the Blade tracking teeth are pointing in the wrong direction when you hold the adjustment handle blade up to the machine, you will have to turn it inside out.

To do this, hold the blade with both hands and rotate see blade section of this manual. Page 24 between the wheels. The bandsaw achieves this by tensioning the blade and thus stretching it. The next complication is that the blade heats up while cutting the wood and expands its length. This allows the blade to become slacker and lose its tension.

To overcome this, the bandsaw has a compression spring that allows for the expansion and keeps a constant pressure on the blade. Page 25 6.

Teeth set insufficient. The set of the teeth is there to create a slot for the back of the blade to pass through. Ideally the body of the blade should not touch the side of the job, but this is not practical, and the best that we can hope for is that little pressure is caused on the blade. Page 26 4. Slightly loosen the clamp screws and adjust the fence to compensate. You may have to do several fine adjustments, and it is better to do several small adjustments until you become skilled at the procedure.

Page 27 Refit all the guards and close the doors. Replace the table insert and check that the blade moves freely through the table insert. Check that all wrenches and loose parts are removed from the machine. Plug the machine into the power. Turn the machine on for a second and switch off. Watch how the blade runs.

Page 28 Laguna Guide system. As with the roller guide systems, the Laguna Guide system will damage your blade if it is not adjusted correctly. The guide blocks must not come in contact with the teeth of the blade. Page 29 5. The Laguna guide system uses ceramic to support and guide the blade. This has many advantages, very poor conductor of heat, very resistant to wear, etc. The disadvantage is that it is very brittle, so the guides must never be dropped, exposed to hard knocks, hit with hard objects or used with badly welded blades.

Page 30 Top guide 1. Loosen the side guides. Rotate the blade by hand and ensure that it is tracking consistently in the correct position. Loosen the rear guide clamp screw and push the guide forward so that it just touches the back of the blade. The blade has a lot of advantages such as superior surface finish to the cut, thin kerf low wood wastage , ability to be re-sharpened, will cut hard woods and a long life. Page 32 Changing the fence height 1. Loosen the two clamp screws that are located on the cast-iron bracket.

Slide the aluminum fence off the cast iron bracket. Slide the aluminum fence back onto the bracket using the second slot and retighten the clamp screws. Resawing Clamp screws Resawing is the process of cutting a board in half along its height. Page 33 smaller the set, the smaller the saw cut, and the larger the radius that can be cut, but the wood is wasted less.

On tipped blades Resaw King , there is no set, as the tip is wider than the backing material. Thickness The thicker the blade, the stiffer the blade, and the straighter the cut. Page 34 Pitch that is Too Coarse The blade has a short cutting life. The teeth wear excessively. The bandsaw vibrates. Width The dimension from the back of the blade, to the front of the teeth. The wider the blade, the stiffer the blade and the straighter the cut.

Lathe Tools Grind Zip Code Making Picture Frames With Hand Tools Youtube Jet Wood Vise