Kreg Jigs can help you drill what are known as pocket holes, which allow screws to be inserted at an angle. Because the screws run along the grain of the wood rather   Set your drill bit collar to the correct depth. Line the pocket hole drill bit up with the specifications indicated on the base of the jig. The step (the place on the bit where it narrows to a point) should be even with the notch that corresponds to the thickness of your board. Slide the depth collar to the appropriate height and tighten it using an Allen wrench.[2] X Research source. The depth collar is slightly wider than the guide holes of the jig, and will keep you from drilling too far into the wood. A special pocket hole drill bit should be included with your new Kreg Jig. Simple steps of how to use Kreg Jig and how to drill pocket holes. Includes screw length sizes chart depending on thickness of wood you're using.  Setting Up. 1. Measure thickness of wood before using Kreg Jig. 2. Adjust the bit collar to appropriate depth. 3. Move up or down to adjust placement of jig. Pocket Hole Drilling. 1. Place wood into the Kreg Jig and clamp. 2. Insert bit into the hole of the jig and drill. Assembling the joints. 1. Use Wood Glue on edges. Kreg Jig K4 Material Depth Guide Locations. The K4 material guide is on the side of the top part that slides up and down, and is held in place by a set screw. Match the line to the edge of the assembly for your material thickness setting. This one is set to 1-½” for drilling into a 2×4. Note: From this angle it looks like I have the line just inside the assembly edge. When looking from the top, it’s dead even.  This may sound silly, but this is how the Kreg manual says to do it, mainly for safety and to ensure you do not damage the bit or jig. With the drill still, place the bit fully into the hole until the tip touches the material. And then back it up ¼”. Finer threads should be reserved for hard, dense varieties of wood like maple and oak. The pocket-hole jig ensures this angle is consistent, and that the bit is held steady as you work — making the process of drilling an angled hole entirely foolproof. Now check kreg jig how to set depth qt email to confirm your subscription. By continuing eepth use our site, you agree to our cookie policy. Related Articles How to. Drill as many holes as you need to create a strong joint that will suit the purposes of your project, then turn det board around and repeat the process on the other end.

Hands down-my Kreg Jig! A Kreg Jig is a tool used to join wood. It makes creating a pocket hole joint easy. Pocket hole joints are made to join wood together. This creates an extremely strong joint for my 2 boards to stay together….

Determine the thickness of your board you are drilling your pocket holes into. Based on the thickness of your board, set your Kreg drill bit and Kreg Jig block to that thickness.

As shown in the video. Place your board into the clamp and drill your pocket holes. The number of pocket holes needed will depend on the width of your board. Cookie Settings. Learn why people trust wikiHow. Download Article Explore this Article parts. Tips and Warnings. Things You'll Need. Related Articles.

Article Summary. Part 1 of Knowing the exact thickness of the board will enable you to drill the pocket holes at just the right angle. The difference of a fraction of an inch could potentially throw off your whole project. Set your drill bit collar to the correct depth.

Line the pocket hole drill bit up with the specifications indicated on the base of the jig. The step the place on the bit where it narrows to a point should be even with the notch that corresponds to the thickness of your board. Slide the depth collar to the appropriate height and tighten it using an Allen wrench.

A special pocket hole drill bit should be included with your new Kreg Jig. Change the placement of the jig. Using the same measurements, adjust the height of the jig to the appropriate position. To do this, loosen the thumbscrew on the back so that you can raise or lower guide hole piece freely. Once the jig is where you want it, tighten the thumbscrew to secure it.

Remember to reset the guide hole piece every time you drill a board of a different size. Secure the jig to the workbench. Clamp the jig down so that it will remain firmly in place. Make sure the guide holes of the jig are facing toward you on the workbench. Part 2 of Clamp the wood into the jig. Place one end of the wooden board vertically against the clamp backing on the opposite side of the jig, then pull the lever to press the clamp tight against it.

Fit the drill bit into the guide holes in the jig. The guide holes should be just large enough to comfortably accommodate the drill bit. Most standard Kreg Jig models will have at least three guide holes so that you can drill as many holes as needed to support the joint.

Should you need more pocket holes than your jig allows, you can make room for more by shifting the wood down in the clamp after drilling your first set. Drill the desired number of pocket holes.

Pull back on the drill as you work to free the guide holes of loose wood chips. Drill as many holes as you need to create a strong joint that will suit the purposes of your project, then turn the board around and repeat the process on the other end. Part 3 of Press the pieces of wood together to form a joint. Thanks for all your efforts.

Hi Robert, yes the calculations should remain the same even for a corner miter joint. Hi, using the thinnest board to set your jig is a good rule of thumb, but the calculator is meant to give more precise results. Pin 15K. Share Inches Metric.

Rikon Sander Polisher Quantum Rockler Plans Zone Rockler Soft Close Hinges 02 Marking Knife Pattern Mod