inch Deluxe Pro Band Saw. Models: JWBSDXPRO. (Shown with optional Rip Fence). JET. New Sanford Road. LaVergne, Tennessee Part No. M Ph.: Revision C1 10/ www.- Copyright © JET. www.- document is bookmarked.  Mounting the Table to the Bandsaw. Grounding Instructions. Volt Operation. Volt Conversion. Extension Cords. Adjustments. Tilting the Table. При составлении этой инструкции особое внимание уделялось возможности быстрого освоения Вами. ленточнопильного станка JWBSDXPRO и обеспечению безопасной работы с ним. Пожалуйста, обратите внимание на ряд указаний, связанных с изучением и хранением инструкции. • Перед вводом станка в эксплуатацию полностью и внимательно изучите данную инструкцию, обратив особое. внимание на указания по технике безопасности. Read/download user manual and instructions for Jet JWBSDXPRO Band Saws.  Model #: JWBSDXPRO - in Deluxe Pro Bandsaw. Product Category: Band Saws. You will need Adobe® Acrobat® Reader to view PDF documents. Download a free copy from the Adobe Web site. View all Band Saws product list. Browse all tools from Jet. Watch DIY videos. Jet Product Catalog. Download product catalog in PDF (e-book) format.

Table Of Contents. Quick Links. This Manual is Bookmarked. Operating Instructions and Parts Manual. Table of Contents. Previous Page.

Next Page. M Ph. Its purpose, aside from machine operation, is to promote safety using accepted operating and maintenance procedures. To obtain maximum life and efficiency from your band saw and to aid in using it safely, please read this manual thoroughly and follow the instructions carefully. Page 4: Warning 4. This band saw is designed and intended for use by properly trained and experienced personnel only.

If you are not familiar with the proper and safe operation of a band saw, do not use until proper training and knowledge have been obtained. Page 5: Save These Instructions blahblahblah Make your workshop child proof with padlocks, master switches or by removing starter keys.

Give your work undivided attention. Maintain a balanced stance at all times so that you do not fall or lean against the blade or other moving parts. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown.

This machine has been designed and constructed to provide years of trouble free operation if used in accordance with instructions set forth in this manual. Page 7: Unpacking - JwbsOs 3 — M5x12 pan head screws approx. Report any damage immediately to your distributor and shipping agent. Read the instruction manual thoroughly for assembly, maintenance and safety instructions. Contents of the Shipping Container Container One With the aid of a second person, lift the saw body out of the shipping container and place onto the stand top.

Page 10 7. Place motor over rubber grommets and fasten to stand top with four hex cap screws, eight flat washers, washers, and four hex nuts, as shown in item C, page 7. See Figure 4. The arrangement of these jet 14 deluxe pro bandsaw manual tab is shown jet 14 deluxe pro bandsaw manual tab Figure 5.

Page 11 To mount table, remove table insert and table pin see Figure Orient the table so that the saw blade will pass through the slot in the table and into the center opening. Continue holding up the table, and turn the With the aid of a second person, lift the saw body out of the shipping container and place onto stand top.

Screw the two small knobs Figure 17 into the threaded holes in the saw body. Slide the pulley cover down over the knobs, and tighten the knobs. Attach trunnion support bracket to saw body Page Grounding Instructions To mount the table, remove pin and insert from the table Jet 14 deluxe pro bandsaw manual tab Orient the table so the saw blade will pass through the slot in the table and into the center opening. Continue holding up the table, and rotate the table so the two screws Page Volt Operation The band saw must comply with all local and national codes after the volt plug is installed.

The band saw with a volt plug should only be connected to an outlet having the same configuration Figure No adapter is available or jet 14 deluxe pro bandsaw manual tab be used with the volt plug.

Page Extension Cords Make sure the cord is in good jet 14 deluxe pro bandsaw manual tab, and heavy enough to carry the current your band saw will draw. An undersized cord will cause a drop in line voltage, resulting in loss of power and overheating.

Page Changing Blades 90 degrees with the blade. If necessary, adjust scale pointer to zero. Changing Blades Blade teeth are sharp! Use care when handling the saw blade. Failure to comply may cause serious injury. Disconnect machine from power source. Loosen blade tension by turning the tension knob counterclockwise Figure Page Adjusting Blade Tracking As you become more experienced with the saw, you may jet 14 deluxe pro bandsaw manual tab it necessary to change the blade tension from the initial setting.

Changes in blade width and the type of material being cut will have an effect on blade tension. Never operate the band saw without all guards in place and in working order. Blade must already be tensioned and tracking properly.

Page 20 Notice the bearing holder on the shaft is eccentric. Index the bearing shaft to another position and slide it back in, making sure the flange on the thumb screw H, Figure 31 properly seats into the groove of the bearing shaft.

Saw stops or will not Fuse blown, or circuit breaker tripped. Cord damaged. Table stop not adjusted correctly. Does not make accurate 45 or 90 Angle pointer not set accurately. Includes four step motor pulley, intermediate pulley, V-belts, fasteners, and mounting instructions with parts list. Page Replacement Parts Blade Width in. Part No. Upper Arm Frame. Table Pin. Guide Block. Upper Support Bracket Post. Description Power Cord Switch To Motor.

Self Tapping Screw Flat Washer Door Latch Assembly. Pan Head Screw JET Plaque. Description Size Top Jet 14 deluxe pro bandsaw manual tab. Stand Leg. Support Plate-long. Support Plate-short. Support Plate-upper. This manual is also suitable for: Jwbsos Jwbss.

Print page 1 Print document 32 pages. Cancel Delete. Sign In OR. Don't have an account? Sign up! Restore password. Upload from disk. Upload from URL.

Item number Description Literature; A: JWBSOS, Bandsaw with Open Stand: Manual: K: 14" Closed Stand Bandsaw, 1HP, 1Ph, /V: Manual: K. The JWBSDXPRO 14" Deluxe Bandsaw from JET (shown here with optional fence) has been designed to meet the needs of today's most demanding woodworkers. Gone are the days of adding a riser block; this 14" bandsaw comes with a massive cast iron frame for increased power that makes it ready to meet all resaw expectations head-on. This manual has been prepared for the owner and operators of a JET Model JWBSDX Band Saw. Its purpose, aside from proper machine operation, is to promote safety through the use of accepted operating and maintenance procedures.

Taytools Jointer Plane Review Key Wen Belt And Disc Sander Review Quality Timber Wolf Blades Coupons Gmbh