Application: Sand small hollow forms and similar decorative turnings frixtion grit sandpaper before applying as many as five coats of gloss lacquer. Joe Friction Polish Woodturning 10 Greiner. Home Shop info Information pages. More good friction polish woodturning 70 it lets you achieve an attractive surface Friction Polish Woodturning Github with only one coat for sealing and successive coats for a deeper luster. I don't use curing oils, though. It is better if it is melted and a proportion of carnauba mixed in.

However, the surface should be sanded with a sanding mesh to a uniform dullness or satin appearance. Then, apply a small amount of satin CA polish with a paper towel Photo D , and buff until dry. Repeat with gloss polish for a gloss finish. General Finishes Water-Based Wood Turners Finish produces a rich amber tone that can be buffed to either a satin sheen or high gloss.

It is food-safe, durable, and acid resistant. It applies easily and cleans up with water. More good news: it lets you achieve an attractive surface with only one coat for sealing and successive coats for a deeper luster.

It is not Friction Polish Woodturning Point seen as a filler for open-grain woods. Best Uses: Use this finish on salad bowls, platters, salt and pepper mills, and other utility items needing a durable finish. Application: With the lathe off, apply water-based finish with paper towels Photo A or brush it on with a foam brush. When applying multiple coats, the first application will dry in 30 to 45 Friction Polish Woodturning Uk minutes. Apply additional coats in 30 minutes. The final finish requires five to seven days to cure to be food-safe.

Gloss spray lacquer produces a glass-clear coating that goes on quickly. I prefer spraying over brushing. It dries fast and lets you reapply it in 30 minutes, with no sanding in between.

I like gloss lacquer over satin for building depth and because it contains fewer solids. Plus, you can repair it with a wax remover, light sanding, and another coat. Best Uses: Consider lacquer for small and large decorative turnings—vessels and other showy pieces.

Downside: Lacquer is flammable, and its fumes can be a problem. Spray only in well-ventilated areas and away from heat sources. Application: Sand small hollow forms and similar decorative turnings through grit sandpaper before applying as many as five coats of gloss lacquer. Rotate the turning for an even coat all around. Once dry, use steel wool with clear Briwax to level the surface Photo B. Buffing with a buffing wheel and carnauba wax will bring out the shine.

For a satin finish, skip the steel wool and wax and apply a final coat of satin lacquer finish. Watco Penetrating Danish Oil, Natural, is a blend of boiled linseed oil and varnish that penetrates, seals, and adds a low luster. While it comes in several shades, such as natural, walnut, cherry, and golden oak, I find that natural is the obvious choice for all woods. It applies easily, though it takes time to achieve the desired result.

The final finish is relatively soft, somewhat durable, and repairs quickly. And while it dries slowly, it produces a warm amber tone. Best Uses: Watco Penetrating Danish Oil works well for general turnings and furniture such as the stool legs and seat shown below. Downside: Watco Penetrating Danish Oil dries slowly, typically taking several hours. In fact, I like to wait 24 hours before reapplication. Take care to properly dispose of your oily paper towels to avoid a spontaneous combustion fire.

The product results in a satin sheen only. Application: With the lathe off, wipe on a full wet coat of oil using a paper towel Photo A , and allow it to penetrate into the wood for 15 to 20 minutes. Then wipe off the excess and burnish it into the wood with a dry paper towel. This is not the same as burnishing raw wood with sandpaper. Allow the coat to dry 24 hours or more, and then reapply to build three to five coats over the course of several days or weeks.

When the piece is completely cured again, 24 hours after the final coat , apply a coat of wax using steel wool Photo B. Finally, buff the wood surfaces to achieve a pleasing satin sheen. One popular category used to finish the pepper and salt mills on page 38 includes friction finishes such as Hut Crystal Coat and Mylands High Build Friction Polish. When correctly applied, the end result is a glowing high-gloss, one-coat finish executed in record time.

Downside: Because of its alcohol base, oils from your hands can degrade a friction finish over time. Other ingredients include petroleum distillates, shellac, and waxes, making the finish highly flammable. Its fumes can irritate. Should you need to you can use Methylated Sprit based Thinners to clean. Highly flammable. Additional Information Size ml, 1L. Related Products.

Wishlist Your wishlist is currently empty. View All Remove All. Compare No products to compare Compare Clear all. There's some grain raising and drying issues I haven't quite worked through yet. I've also seen some homebrew varnishes. I'm not interested in creating a lot more work. Quick, easy, and you don't have to make your own. Mike Peace. I agree with Kurt I use the HUT friction polish on almost all of my small turnings including boxes because it is so easy.

It is a Tripolis in wax compound that helps polish the piece, typically before applying a friction finish like HUT Crystal Coat or Mylands friction finish which I have not used but is supposed to be similar to HUT. GA Darling. I have a recipe for a friction polish that I'm am going to have to dig for. Keep an eye on this posting and I will post the recipe as soon as I find what I did with it.

From what I remember, it worked very well. Did it add more protection without a lot of added labor time? I can't say for sure. At the time it was the only one that had results that I liked. Jake Debski. The only "home brew" that I ever used was no more effective than Crystal Coat.

Like the Hut product it must be shaken before and during use because it is an emulsion. I must be watching too many Christmas movies. I glanced at the main post and thought it Said Hebrew instead of Homebrew. Man I need new glasses. Judging by the Ubeaut Shellawax name and use, some mix of solvent, shellac and wax would be in there.

I like to keep things simple. I often apply a coat of MinWax wipe on poly on the lathe , wait four hours, the apply TreeWax. I admit that I don't always wait the full four hours. Ron Sardo Guest. Click to expand

Pdc Machines Stock Guide Record Woodworking Vise For Sale Framework Homak Gun Cabinet Replacement Locks Example Woodworking Plans Using Pallet Wood Wall