Hilti Rail Catalogue

Always keep these operating instructions together with the appliance. Ensure that the operating instructions are with the appliance when it is given to other persons. You can find the illustrations at the beginning of the operating instructions. CAUTION Draws attention to a potentially dangerous situation that could lead to slight personal injury or damage to the equipment or other property.

NOTE Draws attention to an instruction or other useful information. Location of identification data on the module The type designation is shown on the appliance. Always refer to this information when contacting our representative or service center. Type: Serial no. The dust removal module can be quickly and easily attached to the power tool, i.

The dust removal module is not suitable for use when chiseling or drilling in metals. Please observe national regulations applicable to working with materials hazardous to the health e. The appliance is intended for professional use. The appliance may be operated, serviced and repaired only by authorized, trained personnel. This personnel must be informed of any special hazards that may be encountered.

The appliance and the power tool may present hazards when used incorrectly by untrained personnel or when used not as directed. In order to avoid the risk of injury, use the appliance only in conjunction with the Hilti rotary hammers named above.

Accessories are available from your Hilti Center or can be ordered online at www. Read all instructions! Observe all applicable safety rules and the operating instructions for the Hilti rotary hammer used.

Failure to observe the instructions could lead to serious personal injury. Certain kinds of dust are classified 7 Printed: Material containing asbestos must only be treated by dust removal system te drs-6-a case pdf. Where the use of a dust-extraction device is possible it shall be used.

When indicated wear a respirator appropriate for the type of dust generated. Ensure that the workplace is well ventilated. Follow dust removal system te drs-6-a case pdf requirements for the materials you want to work with.

Accordingly, the container should be emptied regularly. Wear respiratory protection when doing this. NOTE The suction fan incorporated in the dust module is driven by the motor of the Dust Removal System Te Drs 6 A Case Unity tool by way of a push-in coupling. The toothing on the rotor shaft meshes with the toothed sleeve on the dust module. Avoid touching the drive pinion.

Press the release buttons and hold them in this position. Pull the dust removal module downwards away from the power tool. This corresponds to a drill bit working length of mm. The stroke must be adjusted if shorter drill bits are used. CAUTION When the locking ring is opened, the telescopic dust removal system te drs-6-a case pdf is released and it may jump out a distance dust removal system te drs-6-a case pdf up to mm under spring pressure.

Wear eye protection. Release the locking ring. Press the power tool with drill bit fitted against a wall until the tip of the drill bit touches the wall. Tighten the locking ring. Release the end stop. Slide the end stop to the required drilling depth. Secure the end stop. Use the appliance only in conjunction with the power tools listed in section 2. Failure to observe this point may present a risk of personal injury.

Hold the tool horizontally and allow it to run for a short time. This ensures that any dust remaining in parts of the dust removal module are drawn into the dust container. Dust removal system te drs-6-a case pdf the dust container downwards away from the module. Empty the dust container by tapping it lightly. Avoid releasing an excessive amount of dust into the air.

Push the empty dust container back into the dust module from below until it engages. When fitting a new dust container, first dust removal system te drs-6-a case pdf the protective cover. Pull back the rib on the rear of the suction head. Pull the old suction head upwards out of its guide. Press the new suction head into the guide until it engages.

Use only a dry brush and a cloth to clean the appliance. Do not operate the appliance if parts are damaged or when the controls do not function faultlessly. If necessary, the appliance should be repaired at a Hilti repair center.

Emptying the dust container The suction head is defective. Replacing the suction head 8 Disposal Most of the materials from which Hilti tools or appliances are manufactured can be recycled.

The materials must be correctly separated before they can be recycled. In many countries, Hilti has Dust Removal System Te Drs 6 A Case Javascript already made arrangements for taking back old tools and appliances for recycling.

Ask Hilti customer service or your Hilti representative for further information. Download PDF advertisement.

Dust removal system TE DRSA box 1 Quick-release chuck TE 2M/7C/7A/6A Li 1 Drilling and Demolition Ordering designation Description Sales pack quantity Item number TE 2 Rotary Hammer 1 X Rotary hammer TE 2 V, 1 X case 1 Rotary hammer TE 2 Technical data Rated power W Optimum drilling diameter in concrete 5. Dust removal system TE DRSA case # Documents & Videos. Dust removal system TE DRSA case # Arrange a Demo & Support. Ask a Question. Register to make the most of the Hilti website. Do you want to be an online customer? Register to create an account now. Find out more about our delivery services ;. On-board vacuum system for convenient dust collection TE DRSA: Page Dust removal system TE DRSA box 1 pc. Quick-release chuck TE 2M/7C/7A/6A Li. Drilling in wood or metal 1 Dust Removal System Te Drs 6 A Case Mac pc. Cordless Systems. 1x Cordless combihammer TE A36, 1x Case 1 pc.

Good Wood For Turning 500 Round Router Bits Youtube Kreg Jig Drill Bit Guide Us