Share it with us! I love the comic relief you've integrated into the video More info For more information on Kreg products visit www. In order to keep things from getting messed up, I first lay drawer lock router bit uk yahoo and cut all the drawer fronts and backs I had a few mistakes where the piece tilted a bit as I pushed through the cut, and I had to re-do those pieces. More About wordsnwood ». Hi Christopher.

With the router table properly set up, I proceeded with batch cutting all of the drawer pieces. In order to keep things from getting messed up, I first lay out and cut all the drawer fronts and backs You need to be careful with the sides, to hold them perfectly perpendicular with the end flat on the table as you cut them. I had a few mistakes where the piece tilted a bit as I pushed through the cut, and I had to re-do those pieces. I then moved on and cut rabbets along the bottom of the drawers, to h hold the bottoms.

I cut the back of the drawer shorter, so that the bottom can slide in and out. I also cut out the bottoms. None of that was filmed, as the focus of this article was just on the joinery. With the drawer pieces ready, it is now just a matter of adding glue to the ends and then alinging and clamping the pieces. I slid in the plywood bottoms immediately, as they help with ensuring that the drawer box is square.

Here is one shot showing a nice tight drawer corner joint. The two drawer pieces lock together securely, and the joint is closed and flush. In the interests of full honesty, here is also a photo of one of my Fortunately this joint was at the back of a drawer where it will almost never been seen. Otherwise I would try to fill this with sawdust and glue to close the gap, or redo the joint entirely. Note that thet joint is still strong, it just is a bit ugly.

I suspect this might have been caused by those problems I had with the side pieces wiggling a bit while being cut on the router table.

And that is all for now. This article was just about a drawer joinery method. I hope you found something useful in this article!

This is a simple drawer joint, and after initial setup you can cut out your drawer joinery very quickly. Note that the drawers are by no means finished at this point. This is just the drawer bodies. Later on I will be adding nice fronts to these drawers. Thanks for reading. For more projects, going back years, please visit my woodworking web site at www.

I love the comic relief you've integrated into the video As well Drawer Lock Router Bit Uk Not Found as the educational part, considering the name of this place. Introduction: The Drawer Lock Joint. By wordsnwood Words N Wood Follow. When making drawers one of Drawer Lock Router Bit On Plywood Jump the cuts will be across the face grain. This can lead to a lot of tear out and chipping on the face. Drawer locks can also be created on the table saw using a dado head. This is another great way to create lock joints.

You should also check out our content on different types of joinery. For more information on Kreg products visit www. Click here to cancel reply. Hi Curtis. I believe that you can use it on any thickness by making the proper adjustments to your router table fence, but Whiteside suggests other bits in their product line for thicker stock. I think it would be really hard for me to cut into the fence for zero clearance.

I paid a lot of money for my Jessem fence. This would mean my fence would be cut for a specific thickness of stock. You can always take the stock fence off and replace it, temporarily, with an MDF or melamine shop-made face. This was very useful. Thank you! Hi Dennis.

The step where you cut into the fence is to create zero clearance around it. You can use a sacrificial fence for this. A backer board can be used behind the piece as you push it through the cut, which will reduce the chance for blow-out on the trailing edge of the cut.

I would 1st start with a sacrificial fence mounted and then make my adjustments. I would never purposely cut into my Kreg fence! That really surprised me! While your on the subject demonstrate the lock miter bit which is even more fidgety to dial in, accordingly highly recommend using a router lift with a bit height locking feature. Hi Christopher. It is mounted on a shop-made cabinet that George built. I was using my Leigh RTJ They did not recommend using plywood.

He used a zero clearance fence to avoid chipping. Is there something equivalent I could do when cutting my dovetails. Dovetails can look so nice when using baltic birch when it works. Hi Bill. The pin and socket board should, then, be backing up the face of the tail board to help reduce chipping there.

The folks at Leigh are very sharp. It would be worth a call to them to see if they have additional suggestions. In other words changing the fence position moves the groove to position the side correctly, but it also changes how it cuts the tongue, so it compounds the adjustment. Also, changing the bit height not only adjusts the tongue thickness, but it changes where the groove lands on the front, effectively shortening or lengthening the entire drawer box.

All that said this is a great video! For the Baltic birch plywood I see you use, does the shortness of the joint cause a problem with the layers shearing off? I have experienced That little nub is susceptible to breaking off and hence the joint does not hold… any suggestions on how to Locking Drawer Router Bit Client either reinforce or keep from shearing off? Hello Gene. I regularly test the strength of this joint by flipping the drawer over and standing on the bottom of the drawer. Even with that kind Drawer Lock Router Bit On Plywood Flask of stress, this joint stands up every time.

Paul Woodworkers Guild of America. I avoid changing the fence position and the bit height at the same times.

Ece Primus Jointer Plane 30 Wood Carving Kit Home Depot Price Fine Woodworking Kumiko News