P Michener. Need help? That's one reason among many why table saws exist. If radiall raises or lowers as you pull it across the surface, you'll need to adjust the table. Mine still gives me a 12" width of cross cut. Page of 1. If you have not already figured this out, you will need a set of adjusting screws built in to the table to level it.

Login or Sign Up. Logging in Remember me. Log in. Forgot password or user name? Header Ad. Radial Arm Saw Table Dimensions. Posts Latest Activity Photos. Page of 1. Filtered by:.

Previous template Next. I recently came across a Craftsman 10inch Radial Arm Saw in the trash at the curb. Owner said it did't work, but after a little cleaning I plugged it in and it works fine. All adjustments have been made, and major cleaning. Intend to use this for cross cutting for bookcases.

Does anyone have the dimensions for the original table pieces? I have ordered the Emerson Retro kit, but would prefer to use original table dimensions to keep the maximum cross cut.

P Michener. Tags: None. Sorry, I can't help you with the size. But welcome to the site. That's quite a find for you! Do you know about kickback? Ray has a good writeup here Comment Post Cancel. I don't remember the exact dimensions but a few details and have a picture.. I had the 12" model..

The table was in 2 pieces.. You want the fence just far enough forward so it won't trap the blade with the carriage fully returned. The clamping bolts along the back were used to clamp a sacrificial fence between the front and back Radial Arm Saw Stand Emotion table pieces..

You might notice the Back table is in 2 pieces.. That was so I could move the fence back about 6" more inches for wider boards but it left the blade trapped in the fence.. For really wide cuts I'd Cut as far as possible, flip it, mark the kerf out to the uncut edge and align it with the blade..

If you have a fresh hardboard top on the table the kerf cut in the table top makes a good alignment mark. Get a good Negative hook blade.. NEVER rip with it.. They will grab and throw a piece so fast you won't know what happened..

The table is so big it got used as a small work bench half the time. Last edited by sscherin ; , PM. William's Law-- There is no mechanical problem so difficult that it cannot be solved by brute strength and ignorance.

The kit is great. I believe the new kit changes the width of cut by an inch or two. The new table comes with a 3 piece top. The remaining two pieces are adjusted behind what ever fence insert you decide to use. If you want to change the width of cut you can adapt these two pieces for what ever width will work with the new safety guards.

Go ahead andinstall the kit and look at the capacity, it may be OK for your work. Mine still gives me a 12" width of cross cut. I have had Dad's for years now and only recently changed out the table. The operator edge of the table is about 4" beyond the maximum cut for this 9" blade. Keep this edge a little further out than the leading edge of the blade guard. I've not seen a set up like sscherin's. On mine the vertical board used for the fence is pinched between the small, rear table section and the large front table section.

Oh well, maybe pics will be more clear than my feeble explanation. The radial arm features a raised motor and saw blade which cuts stock from above.

This means that the saw blade cuts slightly down into the tabletop on virtually every cut, and over time the table surface becomes filled with grooves from the blade. The saw is engineered in a way that makes it easy to replace this tabletop when it becomes badly marred. If you look closely at the tabletop of a radial arm saw, you will see that it is constructed of three pieces: a large open expanse of tabletop which supports the stock as you cut it; a small vertical fence set just behind the main tabletop; and a narrower section of tabletop that abuts the back of the fence, essentially sandwiching the fence between the two horizontal segments of tabletop.

The bolts that secure the tabletop to the metal Craftsman Radial Arm Saw Table Replacement Ev table of the saw are usually machine bolts that fit into counterbored holes in the tabletop. The counterbores allow the bolts to be recessed far enough down that the saw blades can't contact them when it is drawn across stock during cutting. While any type of sheet good material could be used for the tabletop on a radial arm saw, the best material is medium-density fiberboard MDF. MDF is inexpensive, pretty durable as long as it doesn't get wet and it doesn't splinter when the radial arm saw's blade cuts through it.

Plywood , which is made of layers of wood plies, can begin to splinter and break apart as it becomes filled with saw cuts. The easiest way to replace a tabletop is to remove the old tabletop, cut pieces of MDF to the exact same size as the front tabletop, the fence, and the back tabletop pieces.

You'll then drill the horizontal pieces with the same Old Craftsman Radial Arm Saw Troubleshooting Site counterbored holes as in the old tabletop, then bolt the new tabletop down in exactly the same fashion as the old one. However, there are two critical things to watch for when installing the new tabletop:. When installing a new surface, you will need to make sure that the travel of the radial arm saw is parallel with the table surface at all positions. To test this travel, set the angle of the radial arm saw to the degree cross-cut position, then lower the radial arm saw until the blade is barely touching the surface of the MDF.

Best Rap Countries In The World Videos Carving Kit For Pumpkin Review