Metalworking Equipment for sale | In Stock | eBay

When ordering parts by mail from the mail order house which serves the territory in which you live, selling prices will be furnished on request or parts will be shipped at prevailing prices and you will be billed accordingly. If and when you need repairs or service, call on us to protect your in- vestment in this fine piece of equip- ment. Leave the lathe on the skid -- easier to move. Check bags and cartons for parts.

Read all instructions - hours later. Handle with care -- this lathe is a precision machine. Using a good grease solvent, thoroughly remove the rust-preventive from exposed bed ways -- tops, sides, bottoms -- and from all other machined surfaces.

Next, loosen the carriage lock screw located on top of carriage at right side and move carriage to a clean section of bed. Then, loosen craftsman 12 lathe chuck yourself clamp lever -- move tailstock -- and finish cleaning bed ways.

Use a stiff bristle brush not wire to clean lead screw and carriage rack. Apply a light coating of machine oil to all machined surfaces -- for protection.

After cleaning, move carriage toward tailstock end for better balance. If skid has been removed -- lift by bed feet or under- side of bed -- DO NOT use lead screw, handwheels or levers. Figure 1 Floor legs with table boards make ideal lathe stand. Place bench top on legs and slip four long bolts thru top to hold in place temporarily--DO NOT tighten nuts. Place stand in final location--to provide working room, back leg anchor should be 3 feet from wall.

A reinforced concrete floor is the best foundation. Wood floor should be rigid and capable of supporting the weight of the lathe without deflection -- if the floor is not solid, it should be reinforced, or cut away and a concrete foundation installed.

Make sure the legs rest solidly on the floor and mark the location of mounting holes. Use anchor bolts to secure floor stand Craftsman Lathe Chuck Question to concrete floor -- use lag screws to secure to wood floor. Move stand, craftsman 12 lathe chuck yourself holes and install anchor nuts in craftsman 12 lathe chuck yourself floor -- drill pilot holes for lag screws in wood floor.

NOTE: Doing this elimin- ates excessive shimming between bench top and bed legs when leveling the lathe bed. Recheck the level of stand -- unequal tightening of anchoring bolts may have pulled the stand out of level.

Remove bolts from skid and place lathe on stand -- bolt lathe, stand top and legs together craftsman 12 lathe chuck yourself four long bolts. Bolt countershaft bracket foot see Fig.

Raise countershaft arm E and install pin F in hole under adjusting screw C. Lower countershaft arm until pin F rests on rocker shaft G. Bolt countershaft bracket L to countershaft foot H with four hex cap screws K. Adjust square head set screw M against bed J and lock with jam nut. Place spindle belt N over the 4-step countershaft pulley B.

E Tighten lock screw C A. Figure 6 Mount headstock guard unit B, Fig. Remove knurled collar B, Fig. Insert hinge pin F through the countershaft A and motor base C. Replace washer and knurled collar B on motor base adjusting screw D. Mount motor pulley D, Fig.

Place motor on motor base, craftsman 12 lathe chuck yourself motor pulley D with and parallel to countershaft pulley A ; then bolt motor in place with screws furnished. Place belt E on pulleys. Loosen motor base adjusting screw D, Fig. Move motor base up or down for proper belt tension by adjusting knurled collars B Craftsman 101 Lathe Chuck Flip and E. Tighten motor base adjusting screw.

If there is any question, call your power company. Wire switch and motor so craftsman 12 lathe chuck yourself pulley rotates in a clockwise direction. A wood bench built to the following craftsman 12 lathe chuck yourself will provide a solid foundation for the lathe. Bench should be built using bolted construction. Bench legs should be solid 4" x 4"s, well braced and securely anchored to bench top -- provide legs with lugs for bolting securely to floor.

Make sure the legs rest solidly on the floor. Place wood bench in final location -- to provide work- ing room, back leg should be 3 feet from wall. Mark the location of mounting holes. Use anchor bolts to secure bench to concrete floor — use lag screws to secure to wood floor. Move bench, craftsman 12 lathe chuck yourself holes and install anchor nuts in concrete floor -- drill pilot holes for lag screws in wood floor.

Place shims as required between bench legs and floor until craftsman 12 lathe chuck Craftsman Wood Lathe Chuck Yourself yourself bench is approximately level. NOTE: Doing this elimin- ates excessive shimming between top of bench and bed legs when leveling the lathe bed. Figure 9 Tighten the anchoring bolts or craftsman 12 lathe chuck yourself screws securely.

Recheck the level of bench -- unequal tightening of anchoring bolts may have pulled the bench out of level. Mark the position craftsman 12 lathe chuck yourself four mounting holes C. Move lathe and drill four holes in bench top. Mark and drill four holes A in bench.

When carelessly leveled, the bed may become twisted. Even a slight amount of twist will move centers out of alignment and result in inaccurate work and excessive wear. Make it a habit to regularly check the level of the bed. Clean the bed ways thoroughly. First level bed longitudinally, compensate for variations of bubble readings with thin craftsman 12 lathe chuck yourself shims placed around bolts between bed legs and bench top craftsman 12 lathe chuck yourself bed is level -- refer to Fig.

Shim should be the only contact point be- tween bench top and bed legs. Refer to Fig. Figure 15 2. Next, level the bed at headstock and tail- stock -- see Fig. Place level at right angles to the bed -- use a square to align the level. Do not turn level end for end. Level readings at headstock and tailstock must be identical. Compensate for variation of bubble readings by placing shims be- tween bed legs and bench top at the bolt holes.

Tighten the four mounting bolts securely and recheck level readings. Check level of bed at frequent intervals. Chatter, turning taper, boring taper, facing convex or concave is usually the result of an improperly leveled bed. Wipe the bed and all machined parts with a clean oily cloth at frequent intervals. Use a brush to clean spindle threads, gear teeth, lead screw threads, etc. Remove oil and dirt before applying grease. Remove PLUG.

Turn off motor. Figure 16 2. Raise headstock cover A, Fig. It may be necessary to rotate spindle pulley by hand so gears will mesh. Turn off the motor. Push on lock pin Dand turn spindle pulley by hand until pin slides in, locking bull gear and pulley together.

Move back gear lever C, Fig. Stop motor. Raise headstock guard B, Fig. Move lever backward, tightening the belts. Center position is neutral -- gear train is disengaged and lead screw does not turn. Upper position moves carriage toward tailstock. Lower position moves carriage toward headstock. The indexing holes for this lever are directly below the thread or feed desired.

IN position is toward headstock and meshed with the tooth compound gear K. OUT position is away from the headstock and meshes with the tooth compound gear J. The position of the sliding gear IN or OUT is shown on the chart in the same row as thread or feed desired.

After gears are properly meshed, tighten the lock. Be sure to allow sufficient clear- ance between the two meshing gears. If quick-change levers do not index, do not force, merely rotate spindle by hand until levers slide easily into position. The apron, anchored to front of carriage, contains the power cross and longitudinal feed controls.

Talking about modern tools for woodworking, one of the first tools that we could come up with is the pocket hole jig for making pocket holes. Pocket hole joints make it very easy to assemble pieces of wood together very fast and easily using pocket screws, and a pocket hole jig makes it even easier for you to drill this pocket holes on the wood pieces you’re planning to join. Feb 27,  · Produce a video yourself, and post it here! STAFF, MEMBER, AND SPONSOR VIDEOS. No, we are not WeTube, but some of our members and staff have created videos to help our members learn how to do things. Craftsman Lathe - Newbee Questions. Today at PM; budzinsk; BENCHMASTER MFG. CO. Threads 28 Messages 12 Messages When I arrived at the turning seminar, we were handed 8-inch bowl blanks and assigned a workstation, which consisted of a small Jet lathe, a screw chuck, four jaw chuck, and three carbide turning tools. I was a bit disappointed not to see a traditional bowl gouge, but what did I know at that time.

Under Bed Drawer Nz Off Kenneth Copeland Jet Planes Quote Second Hand Woodwork Bench Year